參數資料
型號: IS42S83200B-7T
廠商: INTEGRATED SILICON SOLUTION INC
元件分類: DRAM
英文描述: 32Meg x 8, 16Meg x16 256-MBIT SYNCHRONOUS DRAM
中文描述: 32M X 8 SYNCHRONOUS DRAM, 5.4 ns, PDSO54
封裝: PLASTIC, TSOP2-54
文件頁數: 49/62頁
文件大小: 646K
代理商: IS42S83200B-7T
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
PRELIMINARY INFORMATION
Rev. 00E
05/25/06
49
ISSI
IS42S83200B, IS42S16160B
DON'T CARE
CLK
COMMAND
BANK n
BANK m
ADDRESS
DQ
T0
T1
T2
T3
T4
T5
T6
T7
NOP
NOP
NOP
NOP
NOP
NOP
D
OUT
a
D
OUT
a+1
D
OUT
b
D
OUT
b+1
COL a
CAS Latency - 3 (BANK n)
CAS Latency - 3 (BANK m)
t
RP - BANK n
t
RP - BANK m
RBANK n
BANK m
Page Active
READ with Burst of 4
Interrupt Burst, Precharge
Idle
Page Active
READ with Burst of 4
Precharge
Internal States
COL b
DON'T CARE
CLK
COMMAND
BANK n
BANK m
ADDRESS
DQM
DQ
T0
T1
T2
T3
T4
T5
T6
T7
NOP
NOP
NOP
NOP
NOP
NOP
D
OUT
a
D
IN
b
D
IN
b+1
D
IN
b+2
D
IN
b+3
COL a
BCOL b
CAS Latency - 3 (BANK n)
t
RP - BANK n
t
DPL - BANK m
BANK n
BANK m
READ with Burst of 4
Interrupt Burst, Precharge
Idle
Page Active
WRITE with Burst of 4
Write-Back
Internal States
Page Active
BURST READ/SINGLE WRITE
The burst read/single write mode is entered by programming
the write burst mode bit
(M9)
in the mode register to a logic 1.
In this mode, all
WRITE
commands result in the access of a
single column location (burst of one), regardless of the
programmed burst length. READ commands access
columns according to the programmed burst length and
sequence, just as in the normal mode of operation (M9 = 0).
CONCURRENT AUTO PRECHARGE
An access command (READ or WRITE) to another bank
while an access command with auto precharge enabled is
executing is not allowed by SDRAMs, unless the SDRAM
supports CONCURRENT AUTO PRECHARGE.
ISSI
SDRAMs support CONCURRENT AUTO PRECHARGE.
Four cases where CONCURRENT AUTO PRECHARGE
occurs are defined below.
READ with Auto Precharge
1. Interrupted by a READ (with or without auto precharge):
A READ to bank m will interrupt a READ on bank n, CAS
latency later. The PRECHARGE to bank n will begin
when the READ to bank m is registered.
2. Interrupted by a WRITE (with or without auto precharge):
A WRITE to bank m will interrupt a READ on bank n when
registered. DQM should be used three clocks prior to the
WRITE command to prevent bus contention. The
PRECHARGE to bank n will begin when the WRITE to
bank m is registered.
READ With Auto Precharge interrupted by a READ
READ With Auto Precharge interrupted by a WRITE
相關PDF資料
PDF描述
IS42S83200B-7TI 32Meg x 8, 16Meg x16 256-MBIT SYNCHRONOUS DRAM
IS42S83200B-7TL 32Meg x 8, 16Meg x16 256-MBIT SYNCHRONOUS DRAM
IS42S83200B-7TLI 32Meg x 8, 16Meg x16 256-MBIT SYNCHRONOUS DRAM
IS42S16160B 32Meg x 8, 16Meg x16 256-MBIT SYNCHRONOUS DRAM
IS42S16160B-6T 32Meg x 8, 16Meg x16 256-MBIT SYNCHRONOUS DRAM
相關代理商/技術參數
參數描述
IS42S83200B-7TI 功能描述:動態隨機存取存儲器 256M 3.3v 32Mx8 143MHz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42S83200B-7TI-TR 功能描述:動態隨機存取存儲器 256M 3.3v 32Mx8 143MHz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42S83200B-7TL 功能描述:動態隨機存取存儲器 256M 3.3v 32Mx8 143MHz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42S83200B-7TLI 功能描述:動態隨機存取存儲器 256M 3.3v 32Mx8 143MHz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42S83200B-7TLI-TR 功能描述:動態隨機存取存儲器 256M 3.3v 32Mx8 143MHz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube