參數資料
型號: IS42S81600A-7TLI
廠商: INTEGRATED SILICON SOLUTION INC
元件分類: DRAM
英文描述: 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
中文描述: 16M X 8 SYNCHRONOUS DRAM, 5.4 ns, PDSO54
封裝: LEAD FREE, PLASTIC, TSOP2-54
文件頁數: 17/65頁
文件大?。?/td> 556K
代理商: IS42S81600A-7TLI
ISSI
24
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
ADVANCEDINFORMATION
Rev. 00A
06/01/02
IS42S81600A, IS42S16800A, IS42S32400A
IS42LS81600A, IS42LS16800A, IS42LS32400A
FUNCTIONAL DESCRIPTION
The 128Mb SDRAMs are quad-bank DRAMs which operate
at 2.5V or 3.3V and include a synchronous interface (all
signals are registered on the positive edge of the clock
signal, CLK). Each of the 16,777,216-bit banks is organized
as 4,096 rows by 256 columns by 16 bits.
Read and write accesses to the SDRAM are burst oriented;
accesses start at a selected location and continue for a
programmed number of locations in a programmed
sequence. Accesses begin with the registration of an AC-
TIVE command which is then followed by a READ or WRITE
command. The address bits registered coincident with the
ACTIVE command are used to select the bank and row to
be accessed (BA0andBA1selectthebank,A0-A11selecttherow).
The address bits(A0-A7)registered coincident with the READ
or WRITE command are used to select the starting column
location for the burst access.
Prior to normal operation, the SDRAM must be initialized.
The following sections provide detailed information covering
device initialization, register definition, command
descriptions and device operation.
Initialization
SDRAMs must be powered up and initialized in a
predefined manner.
The 128M SDRAM is initialized after the power is applied to
VDD and Vddq (simultaneously) and the clock is stable.
A 200s delay is required prior to issuing any command
other than a COMMAND INHIBIT or a NOP. The COMMAND
INHIBIT or NOP may be applied during the 100us period and
should continue at least through the end of the period.
With at least one COMMAND INHIBIT or NOP command
having been applied, a PRECHARGE command should be
applied once the 100s delay has been satisfied. All banks
must be precharged. This will leave all banks in an idle state
where two AUTO REFRESH cycles must be performed. After
theAUTOREFRESHcyclesarecomplete, theSRDRAMisthen
ready for mode register programming.
The mode register and extended mode registers should be
loaded prior to applying any operational command because
it will power up in an unknown state.
相關PDF資料
PDF描述
IDT71V433 32K x 32 3.3V Synchronous SRAM Flow-Through Outputs
IDT71V65602 256K x 36, 512K x 18 3.3V Synchronous ZBT SRAMs 2.5V I/O, Burst Counter Pipelined Outputs
IDT71V65602S-100BG 256K x 36, 512K x 18 3.3V Synchronous ZBT SRAMs 2.5V I/O, Burst Counter Pipelined Outputs
IDT71V65602S-100BGI 256K x 36, 512K x 18 3.3V Synchronous ZBT SRAMs 2.5V I/O, Burst Counter Pipelined Outputs
IDT71V35781 128K x 36, 256K x 18 3.3V Synchronous SRAMs 3.3V I/O, Pipelined Outputs Burst Counter, Single Cycle Deselect
相關代理商/技術參數
參數描述
IS42S81600AL-7TL 制造商:Integrated Silicon Solution Inc 功能描述:
IS42S81600B-6T 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:16Meg x 8, 8Meg x16 128-MBIT SYNCHRONOUS DRAM
IS42S81600B-6TL 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:16Meg x 8, 8Meg x16 128-MBIT SYNCHRONOUS DRAM
IS42S81600B-7T 功能描述:動態隨機存取存儲器 128M 16Mx8 143Mhz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42S81600B-7TI 功能描述:動態隨機存取存儲器 128M 16Mx8 143Mhz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube