參數資料
型號： IS42S16800B-7T
廠商： INTEGRATED SILICON SOLUTION INC
元件分類： DRAM
英文描述： 16Meg x 8, 8Meg x16 128-MBIT SYNCHRONOUS DRAM
中文描述： 8M X 16 SYNCHRONOUS DRAM, 5.4 ns, PDSO54
封裝： 0.400 INCH, TSOP2-54
文件頁數： 27/60頁
文件大?。?/td> 585K
代理商： IS42S16800B-7T
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. E
05/01/06
27
ISSI
IS42S81600B, IS42S16800B
CLK
CKE
HIGH
COLUMN ADDRESS
AUTO PRECHARGE
NO PRECHARGE
CS
RAS
CAS
WE
A0-A9
A10
BA0, BA1
BANK ADDRESS
A11
READ COMMAND
READS
READ bursts are initiated with a READ command, as shown
in the READ COMMAND diagram.
The starting column and bank addresses are provided with the
READ command, and auto precharge is either enabled or
disabled for that burst access. If auto precharge s enabled, the
row being accessed is precharged at the completion of the
burst. For the generic READ commands used in the following
illustrations, auto precharge is disabled.
During READ bursts, the valid data-out element from the
starting column address will be available following the CAS
latency after the READ command. Each subsequent data-
out element will be valid by the next positive clock edge. The
CAS Latency diagram shows general timing
for each possible CAS latency setting.
Upon completion of a burst, assuming no other commands
have been initiated, the DQs will go High-Z. A full-page burst
will continue until terminated. (At the end of the page, it will
wrap to column 0 and continue.)
Data from any READ burst may be truncated with a subse-
quent READ command, and data from a fixed-length READ
burst may be immediately followed by data from a READ
command. In either case, a continuous flow of data can be
maintained. The first data element from the new burst follows
either the last element of a completed burst or the last desired
data element of a longer burst which is being truncated.
The new READ command should be issued x cycles before
the clock edge at which the last desired data element is
valid, where x equals the CAS latency minus one. This is
shown in Consecutive READ Bursts for CAS latencies of
two and three; data element n + 3 is either the last of a burst
of four or the last desired of a longer burst. The 128Mb
SDRAM uses a pipelined architecture and therefore does
not require the 2n ule associated with a prefetch architec-
ture. A READ command can be initiated on any clock cycle
following a previous READ command. Full-speed random
read accesses can be performed to the same bank, as shown
in Random READ Accesses, or each subsequent READ
may be performed to a different bank.
Data from any READ burst may be truncated with a
subsequent WRITE command, and data from a fixed-length
READ burst may be immediately followed by data from a
WRITE command (subject to bus turnaround limitations).
The WRITE burst may be initiated on the clock edge
immediately following the last (or last desired) data element
from the READ burst, provided that I/O contention can be
avoided. In a given system design, there may be a possi-
bility that the device driving the input data will go Low-Z
before the SDRAM DQs go High-Z. In this case, at least a
single-cycle delay should occur between the last read data
and the WRITE command.
The DQM input is used to avoid I/O contention, as shown
in Figures RW1 and RW2. The DQM signal must be
asserted (HIGH) at least three clocks prior to the WRITE
command (DQM latency is two clocks for output buffers) to
suppress data-out from the READ. Once the WRITE com-
mand is registered, the DQs will go High-Z (or remain High-
Z), regardless of the state of the DQM signal, provided the
DQM was active on the clock just prior to the WRITE
command that truncated the READ command. If not, the
second WRITE will be an invalid WRITE. For example, if
DQM was LOW during T4 in Figure RW2, then the WRITEs
at T5 and T7 would be valid, while the WRITE at T6 would
be invalid.
The DQM signal must be de-asserted prior to the WRITE
command (DQM latency is zero clocks for input buffers) to
ensure that the written data is not masked.
A fixed-length READ burst may be followed by, or truncated
with, a
PRECHARGE
command to the same bank
(provided
that auto precharge was not activated)
, and a full-page burst
may be truncated with a PRECHARGE command to the
same bank. The PRECHARGE command should be issued
x cycles before the clock edge at which the last desired data
element is valid, where x equals the CAS latency minus one.
This s shown n the READ to PRECHARGE diagram for each
Note: A9 is "Don't Care" for x16.
相關PDF資料
PDF描述
IS42S16800B-7TI 16Meg x 8, 8Meg x16 128-MBIT SYNCHRONOUS DRAM
IS42S16800B-7TLI 16Meg x 8, 8Meg x16 128-MBIT SYNCHRONOUS DRAM
IS42S81600B-6T 16Meg x 8, 8Meg x16 128-MBIT SYNCHRONOUS DRAM
IS42S81600B-6TL 16Meg x 8, 8Meg x16 128-MBIT SYNCHRONOUS DRAM
IS42S81600B-7T 16Meg x 8, 8Meg x16 128-MBIT SYNCHRONOUS DRAM
相關代理商/技術參數
參數描述
IS42S16800B-7TI 功能描述:動態隨機存取存儲器 128M 8Mx16 143Mhz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42S16800B-7TI-TR 功能描述:動態隨機存取存儲器 128M 8Mx16 143Mhz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42S16800B7TL 制造商:Integrated Silicon Solution Inc 功能描述:
IS42S16800B-7TL 功能描述:動態隨機存取存儲器 128M 8Mx16 143Mhz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
IS42S16800B-7TLI 功能描述:動態隨機存取存儲器 128M 8Mx16 143Mhz RoHS:否 制造商:ISSI 數據總線寬度:16 bit 組織:1 M x 16 封裝 / 箱體:SOJ-42 存儲容量:16 MB 最大時鐘頻率: 訪問時間:50 ns 電源電壓-最大:7 V 電源電壓-最小:- 1 V 最大工作電流:90 mA 最大工作溫度:+ 85 C 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*