參數資料
型號: IRADK31
廠商: International Rectifier
英文描述: 1/3 HP-Phase Brushless DC(BLDC) Motor Controller Using IR3101/3/4
中文描述: 1 / 3的HP -三相無刷直流(BLDC)電機控制器使用IR3101/3/4
文件頁數: 9/24頁
文件大?。?/td> 403K
代理商: IRADK31
www.irf.com
9
I
I
R
R
A
A
D
D
K
K
3
3
1
1
Jumpers JX1 – JX3
These jumpers are used to connect or disconnect the Sensorless Feedback circuit. Their
defaults are in the open position and not used with the current firmware version provided
with this kit.
Connecting the inverter to the motor
WARNING
SW1 is an AC Input Voltage Selector switch. DO NOT apply 230VAC when this switch
is set to 115VAC – this will result in sever damage to the system and personal injury
due to very high voltage produced by the voltage doubler circuit on the DC bus.
Use a 3-phase connected BLDC motor, rated at 1/3 HP or less. Provide a 3-wire, 2A
minimum rated cable for the motor connection, and a 3-wire 2A minimum rated cable for
the AC mains connections. Ensure that the ground connection is also connected to the
earth terminal of J1. The motor phases can be connected in any sequence, only the
rotation direction will be affected. Make all necessary connections, including the serial link
with the PC before applying AC power.
Note: Connecting both the RS-232 serial cable into J5 and the RJ-11 cable into J4
simultaneously will disable communication between the GUI and the system.
When operating the motor, only connect the serial link cable into J5 and when
programming or debugging the microcontroller, only connect the RJ-11 cable into J4.
8. System Connection and GUI Operation
WARNING
When energized, the power produced by the IRADK31 Board – particularly from the
3-phase inverter – can cause severe equipment damage or personal injury. Always
use the proper precautions when working around the board, or power electronic
equipment. Whenever possible, use the IRADK31 Board with the safety shield
installed.
Connect the IRADK31 board to the motor as illustrated in Figure 2. Ensure that the Voltage
Select switch, SW1, is set to the appropriate voltage being supplied to the board. Set SW4
switch to position “1” to supply AC power to the board. Verify that the Red and Green
LEDs are flashing, indicating that power to the board has been established.
Launch the Microchip Motor Control GUI (MotorControlIR2.exe). The first screen will
appear is the Control Panel as illustrated in Figure 4.
相關PDF資料
PDF描述
IRAM136-0461G iMOTION⑩ Series 4A, 600V Plug N DriveTM Integrated Power Module for Energy Efficient Motor Drives
IRAMS06UP60B Plug N Drive Integrated Power Module for Appliance Motor Drive
IRAMS10UP60APBF Plug N Drive⑩ Integrated Power Module for Appliance Motor Drive
IRAMX16UP60B Integrated Power Hybrid IC for Appliance Motor Drive Applications. 16A, 600V with Internal Shunt Resistor
IRAMX20UP60A 20A, 600V with open Emitter Pins
相關代理商/技術參數
參數描述
IRADK-S10UP60 制造商:International Rectifier 功能描述:
IRAE410 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES
IRA-E410 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES
IRA-E410QW1 制造商:Murata Manufacturing Co Ltd 功能描述:PYROELECTRIC INFRARED SENSOR - Bulk
IRA-E410S1 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES