- 您現在的位置：買賣IC網 > PDF目錄360862 > INA111BU Very High Accuracy Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA111BU |
| 元件分類： | 測量放大器 |
| 英文描述： | Very High Accuracy Instrumentation Amplifier |
| 中文描述： | 極高精度儀表放大器 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 245K |
| 代理商： | INA111BU |
INA111
9
A combination of common-mode and differential input
voltage can cause the output of A
1
or A
2
to saturate. Figure
4 shows the output voltage swing of A
1
and A
2
expressed in
terms of a common-mode and differential input voltages.
For applications where input common-mode range must be
maximized, limit the output voltage swing by connecting the
INA111 in a lower gain (see performance curve “Input
Common-Mode Voltage Range vs Output Voltage”). If
necessary, add gain after the INA111 to increase the voltage
swing.
Input-overload often produces an output voltage that appears
normal. For example, consider an input voltage of +14V on
one input and +15V on the other input will obviously exceed
the linear common-mode range of both input amplifiers.
Since both input amplifiers are saturated to the nearly the
same output voltage limit, the difference voltage measured
by the output amplifier will be near zero. The output of the
INA111 will be near 0V even though both inputs are
overloaded.
INPUT PROTECTION
Inputs of the INA111 are protected for input voltages from
0.7V below the negative supply to 15V above the positive
power supply voltages. If the input current is limited to less
than 1mA, clamp diodes are not required; internal junctions
will clamp the input voltage to safe levels. If the input source
can supply more than 1mA, use external clamp diodes as
shown in Figure 5. The source current can be limited with
series resistors R
1
and R
2
as shown. Resistor values greater
than 10k
will contribute noise to the circuit.
A diode formed with a 2N4117A transistor as shown in
Figure 5 assures low leakage. Common signal diodes such as
the 1N4148 may have leakage currents far greater than the
input bias current of the INA111 and are usually sensitive to
light.
INPUT FILTERING
The INA111’s FET input allows use of an R/C input filter
without creating large offsets due to input bias current.
Figure 6 shows proper implementation of this input filter to
preserve the INA111’s excellent high frequency common-
mode rejection. Mismatch of the common-mode input ca-
pacitance (C
1
and C
2
), either from stray capacitance or
FIGURE 5. Input Protection Voltage Clamp.
FIGURE 4. Voltage Swing of A
1
and A
2
.
INA111
V
O
V+
V+
V
IN
–
V
IN
+
D
1
D
3
D
2
D
4
Diodes:
=
2N4117A
1pA Leakage
R
G
R
1
R
2
A
1
A
2
A
3
10k
10k
10k
10k
R
G
V+
V–
INA111
V
O
= G V
D
G = 1 +50k
R
G
25k
25k
V
CM
–G 2
D
V
2
V
2
V
CM
V
CM
+ G 2
D
相關PDF資料 |
PDF描述 |
|---|---|
| INA114AUE4 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA114BP | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA114BU | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA114 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA114AP | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA111BU | 制造商:Texas Instruments 功能描述:IC SM AMP INSTRUMENTATION |
| INA111BU | 制造商:Texas Instruments 功能描述:AMP INSTRUMENTATION SOIC16 111 |
| INA111BUE4 | 功能描述:儀表放大器 High Speed FET-Input Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA114 | 制造商:BB 制造商全稱:BB 功能描述:Precision INSTRUMENTATION AMPLIFIER |
| INA114AG | 制造商:BB 制造商全稱:BB 功能描述:Precision INSTRUMENTATION AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。