- 您現在的位置：買賣IC網 > PDF目錄360862 > INA111BU Very High Accuracy Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA111BU |
| 元件分類： | 測量放大器 |
| 英文描述： | Very High Accuracy Instrumentation Amplifier |
| 中文描述： | 極高精度儀表放大器 |
| 文件頁數： | 7/11頁 |
| 文件大小： | 245K |
| 代理商： | INA111BU |
INA111
7
APPLICATION INFORMATION
Figure 1 shows the basic connections required for operation
of the INA111. Applications with noisy or high impedance
power supplies may require decoupling capacitors close to
the device pins as shown.
The output is referred to the output reference (Ref) terminal
which is normally grounded. This must be a low-impedance
connection to assure good common-mode rejection. A resis-
tance of 2
in series with the Ref pin will cause a typical
device with 90dB CMR to degrade to approximately 80dB
CMR (G = 1).
SETTING THE GAIN
Gain of the INA111 is set by connecting a single external
resistor, R
G
:
Commonly used gains and resistor values are shown in
Figure 1.
The 50k
term in equation 1 comes from the sum of the two
internal feedback resistors. These are on-chip metal film
resistors which are laser trimmed to accurate absolute val-
ues. The accuracy and temperature coefficient of these
resistors are included in the gain accuracy and drift specifi-
cations of the INA111.
The stability and temperature drift of the external gain
setting resistor, R
G
, also affects gain. R
G
’s contribution to
gain accuracy and drift can be directly inferred from the gain
equation (1). Low resistor values required for high gain can
make wiring resistance important. Sockets add to the wiring
resistance, which will contribute additional gain error (pos-
sibly an unstable gain error) in gains of approximately 100
or greater.
DYNAMIC PERFORMANCE
The typical performance curve “Gain vs Frequency” shows
that the INA111 achieves wide bandwidth over a wide range
of gain. This is due to the current-feedback topology of the
INA111. Settling time also remains excellent over wide
gains.
FIGURE 1. Basic Connections
DESIRED
GAIN
R
G
(
)
NEAREST 1% R
G
(
)
1
2
5
10
20
50
100
200
500
1000
2000
5000
10000
No Connection
50.00k
12.50k
5.556k
2.632k
1.02k
505.1
251.3
100.2
50.05
25.01
10.00
5.001
No Connection
49.9k
12.4k
5.62k
2.61k
1.02k
511
249
100
49.9
24.9
10
4.99
G
=
1
+
50k
R
G
(1)
A
1
A
2
A
3
6
10k
10k
10k
10k
7
4
3
8
1
2
V
IN
V
IN
R
G
V+
V–
INA111
G = 1 +50k
R
G
–
+
5
Ref
25k
25k
Load
V
O
= G (V
IN
– V
IN
)
+
–
0.1μF
0.1μF
Pin numbers are
for DIP package.
+
–
V
O
INA111
R
G
Also drawn in simplified form:
V
O
Ref
V
IN
–
V
IN
+
相關PDF資料 |
PDF描述 |
|---|---|
| INA114AUE4 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA114BP | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA114BU | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA114 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA114AP | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA111BU | 制造商:Texas Instruments 功能描述:IC SM AMP INSTRUMENTATION |
| INA111BU | 制造商:Texas Instruments 功能描述:AMP INSTRUMENTATION SOIC16 111 |
| INA111BUE4 | 功能描述:儀表放大器 High Speed FET-Input Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA114 | 制造商:BB 制造商全稱:BB 功能描述:Precision INSTRUMENTATION AMPLIFIER |
| INA114AG | 制造商:BB 制造商全稱:BB 功能描述:Precision INSTRUMENTATION AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。