
IL300
www.vishay.com
Vishay Semiconductors
Rev. 1.7, 23-Sep-11
4
Document Number: 83622
For technical questions, contact:
optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc91000
Notes
Minimum and maximum values were tested requierements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
(1)
Bin sorting:
K3 (transfer gain) is sorted into bins that are ± 6 % , as follows:
Bin A = 0.557 to 0.626
Bin B = 0.620 to 0.696
Bin C = 0.690 to 0.773
Bin D = 0.765 to 0.859
Bin E = 0.851 to 0.955
Bin F = 0.945 to 1.061
Bin G = 1.051 to 1.181
Bin H = 1.169 to 1.311
Bin I = 1.297 to 1.456
Bin J = 1.442 to 1.618
K3 = K2/K1. K3 is tested at I
F
= 10 mA, V
det
= - 15 V.
(2)
Bin categories: All IL300s are sorted into a K3 bin, indicated by an alpha character that is marked on the part. The bins range from “A”
through “J”.
The IL300 is shipped in tubes of 50 each. Each tube contains only one category of K3. The category of the parts in the tube is marked on
the tube label as well as on each individual part.
(3)
Category options: standard IL300 orders will be shipped from the categories that are available at the time of the order. Any of the ten
categories may be shipped. For customers requiring a narrower selection of bins, the bins can be grouped together as follows:
IL300-DEFG: order this part number to receive categories D, E, F, G only.
IL300-EF: order this part number to receive categories E, F only.
IL300-E: order this part number to receive category E only.
COUPLER
Transfer gain stability
I
F
= 10 mA, V
det
= - 15 V
I
F
= 1 mA to 10 mA
I
F
= 1 mA to 10 mA,
T
amb
= 0 °C to 75 °C
Δ
K3/
Δ
T
A
Δ
K3
± 0.005
± 0.25
± 0.05
%/°C
%
Transfer gain linearity
± 0.5
%
PHOTOCONDUCTIVE OPERATION
Frequency response
I
Fq
= 10 mA, MOD = ± 4 mA,
R
L
= 50
Ω
V
det
= - 15 V
BW (- 3 db)
200
kHz
Phase response at 200 kHz
- 45
Deg.
SWITCHING CHARACTERISTICS
PARAMETER
TEST CONDITION
SYMBOL
t
r
t
f
t
r
t
f
MIN.
TYP.
1
1
1.75
1.75
MAX.
UNIT
μs
μs
μs
μs
Switching time
Δ
I
F
= 2 mA, I
Fq
= 10 mA
Rise time
Fall time
ELECTRICAL CHARACTERISTICS
(T
amb
= 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
COMMON MODE TRANSIENT IMMUNITY
PARAMETER
Common mode capacitance
Common mode rejection ratio
TEST CONDITION
V
F
= 0 V, f = 1 MHz
f = 60 Hz, R
L
= 2.2 k
Ω
SYMBOL
C
CM
CMRR
MIN.
TYP.
0.5
130
MAX.
UNIT
pF
dB