參數資料
型號： IDT72V51433L7-5BB8
廠商： IDT, Integrated Device Technology Inc
文件頁數： 18/50頁
文件大?。?/td> 0K
描述： IC FLOW CTRL MULTI QUEUE 256-BGA
標準包裝： 1,000
類型： 多隊列流量控制
安裝類型： 表面貼裝
封裝/外殼： 256-BBGA
供應商設備封裝： 256-BGA（17x17）
包裝： 帶卷 (TR)
其它名稱： 72V51433L7-5BB8
25
IDT72V51433/72V51443/72V51453 3.3V, MULTI-QUEUE FLOW-CONTROL DEVICES
(16 QUEUES) 18 BIT WIDE CONFIGURATION 589,824, 1,179,648 and 2,359,296 bits
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
queues were setup, so when sector 2 is selected the unused outputs
PAE[2:7]
will be don't care states.
Note, that if a read or write operation is occurring to a specific queue, say
queue ‘x’ on the same cycle as a sector switch which will include the queue ‘x’,
then there may be an extra RCLK cycle delay before that queues status is
correctly shown on the respective output of the
PAEn bus.
Sectorscanbeselectedonconsecutiveclockcycles,thatisthesectoronthe
PAEnbuscanchangeeveryRCLKcycle.Also,datacanbereadoutofaqueue
onthesameRCLKrisingedgethatasectorisbeingselected,theonlyrestriction
being that a read queue selection and
PAEnsectorselectioncannotbemade
on the same RCLK cycle.
If 8 or less queues are setup then queues, Queue[0:7] have their
PAEstatus
output on
PAE[0:7]constantly.
Whenthemulti-queuedevicesareconnectedinexpansionofmorethanone
devicethe
PAEnbussesofalldevicesareconnectedtogether,whenswitching
between sectors of different devices the user must utilize the 3 most significant
bits of the RDADD address bus (as well as the 2 LSB’s). These 3 MSB’s
correspond to the device ID inputs, which are the static inputs, ID0, ID1 & ID2.
Please refer to Figure 22,
PAEn - Direct Mode Sector Selection for timing
information. Also refer to Table 2, Read Address Bus, RDADD.
PAEn – POLLED BUS
If FM is HIGH at master reset then the
PAEnbusoperatesinPolled(looped)
mode.Inpolledmodethe
PAEnbusautomaticallycyclesthroughthe2sectors
within the device regardless of how many queues have been setup in the part.
EveryrisingedgeoftheRCLKcausesthenextsectortobeloadedonthe
PAEn
bus. The device configured as the master (MAST input tied HIGH), will take
control of the
PAEn after MRS goes LOW. For the whole RCLK cycle that the
first sector is on
PAEntheESYNC(PAEnbussync)outputwillbeHIGH,forthe
2nd sector, this ESYNC output will be LOW. This ESYNC output provides the
user with a mark with which they can synchronize to the
PAEnbus,ESYNCis
always HIGH for the RCLK cycle that the first sector of a device is present on
the
PAEn bus.
When devices are connected in expansion mode, only one device will be
set as the Master, MAST input tied HIGH, all other devices will have MAST tied
LOW. The master device is the first device to take control of the
PAEnbusand
willplaceitsfirstsectoronthebusontherisingedgeofRCLKafterthe
MRSinput
goes LOW. For the next 3 RCLK cycles the master device will maintain control
ofthe
PAEnbusandcycleitssectorsthroughit,allotherdevicesholdtheirPAEn
outputs in High-Impedance. When the master device has cycled its sectors it
passes a token to the next device in the chain and that device assumes control
of the
PAEn bus and then cycles its sectors and so on, the PAEn bus control
token being passed on from device to device. This token passing is done via
theEXOoutputsandEXIinputsofthedevices(“
PAEExpansionOut”and“PAE
ExpansionIn”).TheEXOoutputofthemasterdeviceconnectstotheEXIofthe
second device in the chain and the EXO of the second connects to the EXI of
the third and so on. The final device in a chain has its EXO connected to the EXI
of the first device, so that once the
PAEnbushascycledthroughallsectorsof
all devices, control of the
PAEnwillpasstothemasterdeviceagainandsoon.
The ESYNC of each respective device will operate independently and simply
indicatewhenthatrespectivedevicehastakencontrolofthebusandisplacing
its first sector on to the
PAEn bus.
When operating in single device mode the EXI input must be connected to
theEXOoutputofthesamedevice.Insingledevicemodeatokenisstillrequired
to be passed into the device for accessing the
PAEn bus.
Please refer to Figure 27,
PAEn Bus – Polled Modefor timing information.
相關PDF資料
PDF描述
IDT72V51256L7-5BB IC FLOW CTRL MULTI QUEUE 256-BGA
HMC36DRYH CONN EDGECARD 72POS DIP .100 SLD
FMC17DRYS CONN EDGECARD 34POS DIP .100 SLD
ACB65DHRR CONN CARD EXTEND 130POS .050"
MIC5320-PGYD6 TR IC REG LDO 3V/1.8V .15A TSOT23-6
相關代理商/技術參數
參數描述
IDT72V51433L7-5BBI 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
IDT72V51436L6BB 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
IDT72V51436L6BB8 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
IDT72V51436L7-5BB 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
IDT72V51436L7-5BB8 功能描述:IC FLOW CTRL MULTI QUEUE 256-BGA RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*