IDT72V3640/50/60/70/80/90 3.3V HIGH DENSITY SUPERSYNC IITM
參數資料
型號： IDT72V3680L6PFG
廠商： IDT, Integrated Device Technology Inc
文件頁數： 44/46頁
文件大?。?/td> 0K
描述： IC FIFO SYNC 16384X36 128QFP
標準包裝： 36
系列： 72V
功能： 異步，同步
存儲容量： 576K（16K x 36）
數據速率： 166MHz
訪問時間： 4ns
電源電壓： 3.15 V ~ 3.45 V
工作溫度： -40°C ~ 80°C
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-TQFP（14x20）
包裝： 托盤
其它名稱： 72V3680L6PFG
800-1537
7
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT72V3640/50/60/70/80/90 3.3V HIGH DENSITY SUPERSYNC IITM 36-BIT FIFO
1,024 x 36, 2,048 x 36, 4,096 x 36, 8,192 x 36, 16,384 x 36 and 32,768 x 36
OCTOBER 22, 2008
NOTE:
1. Inputs should not change state after Master Reset.
2. These pins are for the JTAG port. Please refer to pages 42-45 and Figures 31-33.
PIN DESCRIPTION (PBGA PACKAGE ONLY)
Symbol
Name
I/O
Description
ASYR(1)
Asynchronous
I
A HIGH on this input during Master Reset will select Synchronous read operation for the output port. A LOW
Read Port
will select Asynchronous operation. If Asynchronous is selected the FIFO must operate in IDT Standard mode.
ASYW(1)
Asynchronous
I
A HIGH on this input during Master Reset will select Synchronous write operation for the input port. A LOW
WritePort
will select Asynchronous operation.
TCK(2)
JTAG Clock
I
Clock input for JTAG function. One of four terminals required by IEEE Standard 1149.1-1990. Test operations of the
device are synchronous to TCK. Data from TMS and TDI are sampled on the rising edge of TCK and outputs change
on the falling edge of TCK. If the JTAG function is not used this signal needs to be tied to GND.
TDI(2)
JTAG Test Data
I
One of four terminals required by IEEE Standard 1149.1-1990. During the JTAG boundary scan operation, test data
Input
seriallyloadedviatheTDIontherisingedgeofTCKtoeithertheInstructionRegister,IDRegisterandBypassRegister.
An internal pull-up resistor forces TDI HIGH if left unconnected.
TDO(2)
JTAG Test Data
O
One of four terminals required by IEEE Standard 1149.1-1990. During the JTAG boundary scan operation, test data
Output
seriallyloadedoutputviatheTDOonthefallingedgeofTCKfromeithertheInstructionRegister,IDRegisterandBypass
Register. This output is high impedance except when shifting, while in SHIFT-DR and SHIFT-IR controller states.
TMS(2)
JTAG Mode Select
I
TMSisaserialinputpin.OneoffourterminalsrequiredbyIEEEStandard1149.1-1990.TMSdirectsthedevicethrough
its TAP controller states. An internal pull-up resistor forces TMS HIGH if left unconnected.
TRST(2)
JTAG Reset
I
TRST is an asynchronous reset pin for the JTAG controller. The JTAG TAP controller does not automatically reset
upon power-up, thus it must be reset by either this signal or by setting TMS= HIGH for five TCK cycles. If the TAP
controller is not properly reset then the FIFO outputs will always be in high-impedance. If the JTAG function is used
but the user does not want to use
TRST, then TRST can be tied with MRS to ensure proper FIFO operation. If the
JTAG function is not used then this signal needs to be tied to GND.
PIN DESCRIPTION-CONTINUED (TQFP & PBGA PACKAGES)
SEN
Serial Enable
I
SENenablesserialloadingofprogrammableflagoffsets.
WCLK/
WriteClock/
I
If Synchronous operation of the write port has been selected, when enabled by
WEN, the rising edge of WCLK
WR
WriteStrobe
writes data into the FIFO. If Asynchronous operation of the write port has been selected, WR writes data into the FIFO
on a rising edge in an Asynchronous manner, (
WEN should be tied to its active state). Asynchronous operation of
the WCLK/WR input is only available in the PBGA package.
WEN
WriteEnable
I
WEN enables WCLK for writing data into the FIFO memory and offset registers.
VCC
+3.3V Supply
I
These are VCC supply inputs and must be connected to the 3.3V supply rail.
Symbol
Name
I/O
Description
NOTE:
1. Inputs should not change state after Master Reset.
相關PDF資料
PDF描述
MS27656T13A98S CONN RCPT 10POS WALL MNT W/SCKT
IDT72V283L7-5BC IC FIFO 32768X18 7-5NS 100-BGA
MS27656E13A98S CONN RCPT 10POS WALL MNT W/SCKT
MS27468T21A35PA CONN RCPT 79POS JAM NUT W/PINS
IDT72V3680L7-5BB IC FIFO SS 16384X36 7-5NS 144BGA
相關代理商/技術參數
參數描述
IDT72V3680L6PFG8 功能描述:IC FIFO SS 16384X36 6NS 128-TQFP RoHS:是 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V3680L7-5BB 功能描述:IC FIFO SS 16384X36 7-5NS 144BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V3680L7-5BB8 功能描述:IC FIFO SS 16384X36 7-5NS 144BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V3680L7-5BBI 功能描述:IC FIFO SS 16384X36 7-5NS 144BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V3680L7-5PF 功能描述:IC FIFO SS 16384X36 7-5N 128TQFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*