IDT72V3640/50/60/70/80/90 3.3V HIGH DENSITY SUPERSYNC IITM
參數資料
型號： IDT72V3680L6PFG
廠商： IDT, Integrated Device Technology Inc
文件頁數： 13/46頁
文件大?。?/td> 0K
描述： IC FIFO SYNC 16384X36 128QFP
標準包裝： 36
系列： 72V
功能： 異步，同步
存儲容量： 576K（16K x 36）
數據速率： 166MHz
訪問時間： 4ns
電源電壓： 3.15 V ~ 3.45 V
工作溫度： -40°C ~ 80°C
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-TQFP（14x20）
包裝： 托盤
其它名稱： 72V3680L6PFG
800-1537
20
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT72V3640/50/60/70/80/90 3.3V HIGH DENSITY SUPERSYNC IITM 36-BIT FIFO
1,024 x 36, 2,048 x 36, 4,096 x 36, 8,192 x 36, 16,384 x 36 and 32,768 x 36
OCTOBER 22, 2008
not there are any words present in the FIFO memory. It also uses the Full Flag
function (
FF) to indicate whether or not the FIFO memory has any free space
for writing. In IDT Standard mode, every word read from the FIFO, including
the first, must be requested using the Read Enable (
REN) and RCLK.
If, at the time of Master Reset, FWFT/SI is HIGH, then FWFT mode will be
selected. This mode uses Output Ready (
OR)toindicatewhetherornotthere
is valid data at the data outputs (Qn). It also uses Input Ready (
IR) to indicate
whether or not the FIFO memory has any free space for writing. In the FWFT
mode,thefirstwordwrittentoanemptyFIFOgoesdirectlytoQnafterthreeRCLK
rising edges,
REN = LOW is not necessary. Subsequent words must be
accessed using the Read Enable (
REN) and RCLK.
AfterMasterReset,FWFT/SIactsasaserialinputforloading
PAEandPAF
offsets into the programmable registers. The serial input function can only be
used when the serial loading method has been selected during Master Reset.
SerialprogrammingusingtheFWFT/SIpinfunctionsthesamewayinbothIDT
Standard and FWFT modes.
WRITE STROBE & WRITE CLOCK (WR/WCLK)
IfSynchronousoperationofthewriteporthasbeenselectedvia
ASYW,this
input behaves as WCLK.
A write cycle is initiated on the rising edge of the WCLK input. Data setup
and hold times must be met with respect to the LOW-to-HIGH transition of the
WCLK.ItispermissibletostoptheWCLK. NotethatwhileWCLKisidle,the
FF/
IR, PAF and HF flags will not be updated. (Note that WCLK is only capable of
updating
HF flag to LOW). The Write and Read Clocks can either be
independent or coincident.
IfAsynchronousoperationhasbeenselectedthisinputisWR(writestrobe).
Data is Asynchronously written into the FIFO via the Dn inputs whenever there
is a rising edge on WR. In this mode the WEN input must be tied LOW.
WRITE ENABLE (
WEN )
Whenthe
WENinput isLOW,datamaybeloadedintotheFIFORAMarray
on the rising edge of every WCLK cycle if the device is not full. Data is stored
in the RAM array sequentially and independently of any ongoing read
operation.
When
WENisHIGH,nonewdataiswrittenintheRAMarrayoneachWCLK
cycle.
To prevent data overflow in the IDT Standard mode,
FF will go LOW,
inhibiting further write operations. Upon the completion of a valid read cycle,
FF will go HIGH allowing a write to occur. The FF is updated by two WCLK
cycles + tSKEW after the RCLK cycle.
To prevent data overflow in the FWFT mode,
IR will go HIGH, inhibiting
further write operations. Upon the completion of a valid read cycle,
IR will go
LOW allowing a write to occur. The
IR flag is updated by two WCLK cycles +
tSKEW after the valid RCLK cycle.
WENisignoredwhentheFIFOisfullineitherFWFTorIDTStandardmode.
If Asynchronous operation of the write port has been selected, then
WEN
must be held active, (tied LOW).
READ STROBE & READ CLOCK (RD/RCLK)
IfSynchronousoperationofthereadporthasbeenselectedvia
ASYR,this
inputbehavesasRCLK.A readcycleisinitiatedontherisingedgeoftheRCLK
input. Data can be read on the outputs, on the rising edge of the RCLK input.
ItispermissibletostoptheRCLK. NotethatwhileRCLKisidle,the
EF/OR,PAE
and
HF flagswillnotbeupdated.(NotethatRCLKisonlycapableofupdating
the
HF flag to HIGH). The Write and Read Clocks can be independent or
coincident.
If Asynchronous operation has been selected this input is RD (Read
Strobe) . Data is Asynchronously read from the FIFO via the output register
whenever there is a rising edge on RD. In this mode the
REN input must be
tied LOW. The
OEinputisusedtoprovideAsynchronouscontrolofthethree-
stateQnoutputs.
READ ENABLE (
REN )
WhenReadEnableisLOW,dataisloadedfromtheRAMarrayintotheoutput
register on the rising edge of every RCLK cycle if the device is not empty.
When the
REN input is HIGH, the output register holds the previous data
and no new data is loaded into the output register. The data outputs Q0-Qn
maintain the previous data value.
In the IDT Standard mode, every word accessed at Qn, including the first
word written to an empty FIFO, must be requested using
REN. Whenthelast
word has been read from the FIFO, the Empty Flag (
EF)willgoLOW,inhibiting
further read operations.
RENisignoredwhentheFIFOisempty.Onceawrite
is performed,
EFwillgoHIGHallowingareadtooccur. TheEFflagisupdated
by two RCLK cycles + tSKEW after the valid WCLK cycle.
IntheFWFTmode,thefirstwordwrittentoanemptyFIFOautomaticallygoes
to the outputs Qn, on the third valid LOW-to-HIGH transition of RCLK + tSKEW
after the first write.
RENdoesnotneedtobeassertedLOW. Inordertoaccess
allotherwords,areadmustbeexecutedusing
REN. TheRCLKLOW-to-HIGH
transition after the last word has been read from the FIFO, Output Ready (
OR)
will go HIGH with a true read (RCLK with
REN = LOW), inhibiting further read
operations.
REN is ignored when the FIFO is empty.
If Asynchronous operation of the Read port has been selected, then
REN
must be held active, (tied LOW).
SERIAL ENABLE (
SEN )
The
SEN input isanenableusedonlyforserialprogrammingoftheoffset
registers. The serial programming method must be selected during Master
Reset.
SENisalwaysusedinconjunctionwithLD. Whentheselinesareboth
LOW,dataattheSIinputcanbeloadedintotheprogramregisteronebitforeach
LOW-to-HIGHtransitionofWCLK.
When
SEN is HIGH, the programmable registers retains the previous
settings and no offsets are loaded.
SEN functions the same way in both IDT
Standard and FWFT modes.
OUTPUT ENABLE (
OE)
When Output Enable is enabled (LOW), the parallel output buffers receive
data from the output register. When
OEisHIGH,theoutputdatabus(Qn)goes
into a high impedance state.
LOAD (
LD )
This is a dual purpose pin. During Master Reset, the state of the
LD input,
along with FSEL0 and FSEL1, determines one of eight default offset values for
the
PAEand PAFflags,alongwiththemethodbywhichtheseoffsetregisters
can be programmed, parallel or serial (see Table 2). After Master Reset,
LD
enables write operations to and read operations from the offset registers. Only
theoffsetloadingmethodcurrentlyselectedcanbeusedtowritetotheregisters.
Offset registers can be read only in parallel.
AfterMasterReset,the
LDpinisusedtoactivatetheprogrammingprocess
oftheflagoffsetvalues
PAEandPAF.PullingLDLOWwillbeginaserialloading
or parallel load or read of these offset values.
BUS-MATCHING (BM, IW, OW)
ThepinsBM,IWandOWareusedtodefinetheinputandoutputbuswidths.
DuringMasterReset,thestateofthesepinsisusedtoconfigurethedevicebus
sizes. See Table 1 for control settings. All flags will operate on the word/byte
size boundary as defined by the selection of bus width. See Figure 4 for Bus-
Matching Byte Arrangement.
相關PDF資料
PDF描述
MS27656T13A98S CONN RCPT 10POS WALL MNT W/SCKT
IDT72V283L7-5BC IC FIFO 32768X18 7-5NS 100-BGA
MS27656E13A98S CONN RCPT 10POS WALL MNT W/SCKT
MS27468T21A35PA CONN RCPT 79POS JAM NUT W/PINS
IDT72V3680L7-5BB IC FIFO SS 16384X36 7-5NS 144BGA
相關代理商/技術參數
參數描述
IDT72V3680L6PFG8 功能描述:IC FIFO SS 16384X36 6NS 128-TQFP RoHS:是 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V3680L7-5BB 功能描述:IC FIFO SS 16384X36 7-5NS 144BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V3680L7-5BB8 功能描述:IC FIFO SS 16384X36 7-5NS 144BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V3680L7-5BBI 功能描述:IC FIFO SS 16384X36 7-5NS 144BGA RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V3680L7-5PF 功能描述:IC FIFO SS 16384X36 7-5N 128TQFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*