- 您現在的位置：買賣IC網 > PDF目錄67710 > ICSLV810SI 810 SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 PDF資料下載
參數資料
| 型號： | ICSLV810SI |
| 元件分類： | 時鐘及定時 |
| 英文描述： | 810 SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO20 |
| 封裝： | 0.300 INCH, SOIC-20 |
| 文件頁數： | 7/13頁 |
| 文件大?。?/td> | 241K |
| 代理商： | ICSLV810SI |
Buffer/Clock Driver
MDS LV810 D
3
Revision 062105
Integrated Circuit Systems, Inc.
● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com
ICSLV810
External Components
The ICSLV810 requires a minimum number of external
components for proper operation.
Decoupling Capacitors
Decoupling capacitors of 0.01F must be connected
between VDD and GND, as close to these pins as
possible. For optimum device performance, the
decoupling capacitors should be mounted on the
component side of the PCB. Avoid the use of vias in the
decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be
used. To series terminate a 50
trace (a commonly
used trace impedance) place a 33
resistor in series
with the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
20
.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) The 0.01F decoupling capacitors should be
mounted on the component side of the board as close
to the VDD pins as possible. No vias should be used
between the decoupling capacitors and VDD pins. The
PCB trace to VDD pin should be kept as short as
possible, as should the PCB trace to the ground via.
2) To minimize EMI the 33
series termination resistor,
if needed, should be placed close to the clock output.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICSLV810. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Recommended Operation Conditions
Item
Rating
Supply Voltage, VDD MAX
7 V
All Inputs and Outputs
-0.5 V to VDDA + 1.2 V
Ambient Operating Temperature
-40 to +85
°C
Storage Temperature
-65 to +150
°C
Junction Temperature
125
°C
Soldering Temperature
260
°C
Parameter
Min.
Typ.
Max.
Units
Ambient Operating Temperature
-40
+85
°C
Power Supply Voltage (measured with respect to GND), VDDA
+2.375
+2.625
V
Power Supply Voltage (measured with respect to GND), VDDB
1.425
2.625
V
Power Supply Voltage (measured with respect to GND), VDDC
1.425
2.625
V
相關PDF資料 |
PDF描述 |
|---|---|
| ICSS98UAE877AHLFIT | 98UAE SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PBGA52 |
| ICSS98UAE877AKLFT | 98UAE SERIES, PLL BASED CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQCC40 |
| ICSSSTU3286AHLFT | SSTU SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA96 |
| ICSSSTUA32864BHMLFT | SSTU SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA96 |
| ICSSSTUA32866BHLFT | SSTU SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA96 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IC-SM2L | 制造商:ICHAUS 制造商全稱:ICHAUS 功能描述:LINEAR AMR SENSOR (2 mm) |
| IC-SM2LCHIP | 制造商:ICHAUS 制造商全稱:ICHAUS 功能描述:LINEAR AMR SENSOR (2 mm) |
| IC-SM5L | 制造商:ICHAUS 制造商全稱:ICHAUS 功能描述:LINEAR AMR SENSOR (5 mm) |
| IC-SM5LCHIP | 制造商:ICHAUS 制造商全稱:ICHAUS 功能描述:LINEAR AMR SENSOR (5 mm) |
| IC-SN85 | 制造商:ICHAUS 制造商全稱:ICHAUS 功能描述:INFRARED LED |
發布緊急采購，3分鐘左右您將得到回復。