- 您現在的位置：買賣IC網 > PDF目錄67708 > ICS952001YFT (INTEGRATED DEVICE TECHNOLOGY INC) 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 PDF資料下載
參數資料
| 型號： | ICS952001YFT |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 封裝： | 0.300 INCH, SSOP-48 |
| 文件頁數： | 6/17頁 |
| 文件大?。?/td> | 212K |
| 代理商： | ICS952001YFT |
14
Third party brands and names are the property of their respective owners.
Integrated
Circuit
Systems, Inc.
ICS952001
Preliminary Product Preview
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In
this mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD (logic 1)
power supply or the GND (logic 0) voltage potential. A 10
Kilohm (10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Figure 1 shows a means of implementing this function when
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
a switch or 2 pin header is used. With no jumper is installed
the pin will be pulled high. With the jumper in place the pin
will be pulled low. If programmability is not necessary, than
only a single resistor is necessary. The programming
resistors should be located close to the series termination
resistor to minimize the current loop area. It is more important
to locate the series termination resistor close to the driver
than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS952606YFLFT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS952607YFLF-T | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS952621YFLF-T | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS952621YGLF-T | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS952623YGLFT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS952003 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Programmable Timing Control Hub? for P4? processor |
| ICS952003YFT | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for P4⑩ processor |
| ICS952004 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub⑩ for P4⑩ processor |
| ICS952011 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for P4 processor |
| ICS952011YFT | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for P4 processor |
發布緊急采購，3分鐘左右您將得到回復。