- 您現在的位置：買賣IC網 > PDF目錄9601 > ICS951402AGLFT (IDT, Integrated Device Technology Inc)IC TIMING CTRL HUB P4 48-TSSOP PDF資料下載
參數資料
| 型號： | ICS951402AGLFT |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 13/23頁 |
| 文件大小： | 0K |
| 描述： | IC TIMING CTRL HUB P4 48-TSSOP |
| 標準包裝： | 1,000 |
| 系列： | TCH™ |
| 類型： | 時鐘/頻率發生器，多路復用器 |
| PLL： | 是 |
| 主要目的： | Intel CPU，Timing Control Hub? |
| 輸入： | 晶體 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:19 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 210MHz |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TFSOP（0.240"，6.10mm 寬） |
| 供應商設備封裝： | 48-TSSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 951402AGLFT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁
20
Integrated
Circuit
Systems, Inc.
ICS951402
Advance Information
0660—05/05/05
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In
this mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD (logic 1)
power supply or the GND (logic 0) voltage potential. A 10
Kilohm (10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the series
termination resistor to minimize the current loop area. It is
more important to locate the series termination resistor
close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICL3241ECV | IC 3DRVR/5RCVR RS232 3V 28-TSSOP |
| ICL3241ECB-T | IC 3DRVR/5RCVR RS232 3V 28-SOIC |
| ICL3244ECA-T | IC 3DRVR/5RCVR RS232 3V 28-SSOP |
| GTC06AF-28-21S | CONN PLUG 37POS STRAIGHT W/SCKT |
| M83723/74W1203N | CONN RCPT 3POS JAM NUT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS951402YFLF-T | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for P4 processor |
| ICS951402YGLF-T | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Timing Control Hub for P4 processor |
| ICS951403 | 制造商:ICS 制造商全稱:ICS 功能描述:AMD-K7 System Clock Chip |
| ICS951403YFLF-T | 制造商:ICS 制造商全稱:ICS 功能描述:AMD-K7 System Clock Chip |
| ICS951403YGLF-T | 制造商:ICS 制造商全稱:ICS 功能描述:AMD-K7 System Clock Chip |
發布緊急采購，3分鐘左右您將得到回復。