- 您現在的位置：買賣IC網 > PDF目錄67690 > ICS84314AYLF (INTEGRATED DEVICE TECHNOLOGY INC) 350 MHz, OTHER CLOCK GENERATOR, PQFP32 PDF資料下載
參數資料
| 型號： | ICS84314AYLF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 350 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, LEAD FREE, MS-026BBA, LQFP-32 |
| 文件頁數： | 4/19頁 |
| 文件大?。?/td> | 432K |
| 代理商： | ICS84314AYLF |
84314AY
www.icst.com/products/hiperclocks.html
REV. C JANUARY 27, 2005
12
Integrated
Circuit
Systems, Inc.
ICS84314
350MHZ, CRYSTAL-TO-3.3V/2.5V LVPECL
FREQUENCY SYNTHESIZER W/FANOUT BUFFER
The following component footprints are used in this layout
example: All the resistors and capacitors are size 0603.
POWER AND GROUNDING
Place the decoupling capacitors C14 and C15 as close as pos-
sible to the power pins. If space allows, placing the decoupling
capacitor at the component side is preferred. This can reduce
unwanted inductance between the decoupling capacitor and the
power pin generated by the via.
Maximize the pad size of the power (ground) at the decoupling
capacitor. Maximize the number of vias between power (ground)
and the pads.This can reduce the inductance between the power
(ground) plane and the component power (ground) pins.
If V
CCA shares the same power supply with VCC, insert the RC
filter R7, C11, and C16 in between. Place this RC filter as close
to the V
CCA as possible.
CLOCK TRACES AND TERMINATION
The component placements, locations and orientations should be
arranged to achieve the best clock signal quality. Poor clock signal
quality can degrade the system performance or cause system fail-
ure. In the synchronous high-speed digital system, the clock signal
is less tolerable to poor signal quality than other signals. Any ring-
ing on the rising or falling edge or excessive ring back can cause
system failure. The trace shape and the trace delay might be re-
stricted by the available space on the board and the component
location.While routing the traces, the clock signal traces should be
routed first and should be locked prior to routing other signal traces.
The traces with 50
transmission lines TL1 and TL2
at FOUT and nFOUT should have equal delay and run
adjacent to each other. Avoid sharp angles on the clock
trace. Sharp angle turns cause the characteristic
impedance to change on the transmission lines.
Keep the clock trace on the same layer. Whenever pos-
sible, avoid any vias on the clock traces. Any via on the
trace can affect the trace characteristic impedance and
hence degrade signal quality.
To prevent cross talk, avoid routing other signal traces in
parallel with the clock traces. If running parallel traces is
unavoidable, allow more space between the clock trace
and the other signal trace.
Make sure no other signal trace is routed between the
clock trace pair.
The matching termination resistors R1, R2, R3 and R4 should
be located as close to the receiver input pins as possible.
Other termination schemes can also be used but are not
shown in this example.
CRYSTAL
The crystal X1 should be located as close as possible to the
pins 25 (XTAL1) and 26 (XTAL2). The trace length between
the X1 and U1 should be kept to a minimum to avoid unwanted
parasitic inductance and capacitance. Other signal traces should
not be routed near the crystal traces.
FIGURE 6B. PCB BOARD LAYOUT FOR ICS84314
VIA
X1
U1
R7
VCCA
C5
C1
VCC
C4
C16
GND
C3
PIN 1
C2
C11
ICS84314
350MHZ, CRYSTAL-TO-3.3V/2.5V LVPECL FREQUENCY SYNTHESIZER W/FANOUT BUFFER
TSD
IDT / ICS 350MHZ, CRYSTAL-TO-3.3V/2.5V LVPECL FREQUENCY SYNTHESIZER W/FANOUT BUFFER
ICS84314
12
相關PDF資料 |
PDF描述 |
|---|---|
| ICS84314AY | 350 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| ICS84314AYLFT | 350 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| ICS8431AM-21LF | 350 MHz, OTHER CLOCK GENERATOR, PDSO28 |
| ICS8431AMI-21LF | 350 MHz, OTHER CLOCK GENERATOR, PDSO28 |
| ICS8431CM-01LF | 200 MHz, OTHER CLOCK GENERATOR, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS84314AYLFT | 功能描述:IC SYNTHESIZER 350MHZ 32-LQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS84314AYT | 制造商:ICS 制造商全稱:ICS 功能描述:350MHZ, CRYSTAL-TO-3.3V/2.5V LVPECL FREQUENCY SYNTHESIZER W/FANOUT BUFFER |
| ICS843156AKILF | 功能描述:IC CLK GENERATOR 32VFQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS843156AKILFT | 功能描述:IC CLK GENERATOR 32VFQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS843156AKLF | 功能描述:IC CLK GENERATOR 32VFQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
發布緊急采購，3分鐘左右您將得到回復。