- 您現在的位置：買賣IC網 > PDF目錄360755 > ICS680G-01LFT Networking Clock Synthesizer and Zero Delay Buffer PDF資料下載
參數資料
| 型號： | ICS680G-01LFT |
| 英文描述： | Networking Clock Synthesizer and Zero Delay Buffer |
| 中文描述： | 網絡時鐘合成器和零延遲緩沖器 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 107K |
| 代理商： | ICS680G-01LFT |
Networking Clock Synthesizer and Zero Delay Buffer
MDS 680-01 F
3
Revision 020305
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
●
tel (408) 297-1201
●
www.icst.com
ICS680-01
External Components
The ICS680-01 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01μF must be connected
between VDD (pins 5 and 16) and GND (pins 6 and
15), as close to these pins as possible. For optimum
device performance, the decoupling capacitor should
be mounted on the component side of the PCB. Avoid
the use of vias in the decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be
used. To series terminate a 50
trace (a commonly
used trace impedance) place a 33
resistor in series
with the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
20
.
Crystal Information
The crystal used should be a fundamental mode (do
not use third overtone), parallel resonant. Crystal
capacitors should be connected from pins X1 to ground
and X2 to ground to optimize the initial accuracy. The
value of these capacitors is given by the following
equation crystal caps (pF) = (C
L
-6)x2
In the equation, C
L
is the crystal load
capacitance. So
for a crystal with a 16 pF load capacitance, two 20
pF[(16-6)x2] capacitors should be used
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) The 0.01μF decoupling capacitor should be mounted
on the component side of the board as close to the
VDD pin as possible. No vias should be used between
decoupling capacitor and VDD pin. The PCB trace to
VDD pin should be kept as short as possible, as should
the PCB trace to the ground via.
2) The external crystal should be mounted just next to
the device with short traces. The X1 and X2 traces
should not be routed next to each other with minimum
spaces, instead they should be separated and away
from other traces.
3) To minimize EMI, the 33
series termination resistor
(if needed) should be placed close to the clock output.
4) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers. Other signal traces should be routed
away from the ICS680-01. This includes signal traces
just underneath the device, or on layers adjacent to the
ground plane layer used by the device.
18
VDD
Power
Connect to voltage supply.
19
ICLK
Input
Zero Delay Buffer Input. Weak Internal pull-up.
20
25M
Output
25 MHz reference output clock. Weak internal pull-down when tri-state.
21
S1
Input
Select pin 1. See table above.
22
PDTS
Power
Power-down tri-state. Powers down entire chip and tri-states outputs
when low. Internal pull-up resistor.
23
VDD
Power
Connect to voltage supply.
24
X2
XO
Crystal output. Connect this pin to a crystal. Float for clock input.
Pin
Number
Pin
Name
Pin
Type
Pin Description
相關PDF資料 |
PDF描述 |
|---|---|
| ICS680G-01T | Networking Clock Synthesizer and Zero Delay Buffer |
| ICS6953BI147 | DIFFERENTIAL-TO-LVCMOS / LVTTL ZERO DELAY BUFFER |
| ICS7151A | Spread Spectrum Clock Generator |
| ICS7151AM-50 | Spread Spectrum Clock Generator |
| ICS7151AM-50LF | Spread Spectrum Clock Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS680G-01T | 功能描述:IC SYNTHESIZER/ZD BUFFER 24TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| ICS68-1 | 制造商:Thomas & Betts 功能描述:Cable Accessories Compression Splice Aluminum Orange |
| ICS69-1 | 制造商:Thomas & Betts 功能描述:SEALEEVE |
| ICS6953BI147 | 制造商:ICS 制造商全稱:ICS 功能描述:DIFFERENTIAL-TO-LVCMOS / LVTTL ZERO DELAY BUFFER |
| ICS70-1 | 制造商:Thomas & Betts 功能描述:Cable Accessories Compression Splice Aluminum |
發布緊急采購，3分鐘左右您將得到回復。