參數資料
型號： ICS1700AS
廠商： Electronic Theatre Controls, Inc.
英文描述： QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries
中文描述： QuickSaver充電控制器的鎳鎘和鎳氫電池
文件頁數： 8/24頁
文件大小： 204K
代理商： ICS1700AS
8
ICS1700A
Indicators: CMN, PFN, OTN Pins
The controller has three outputs for driving external indicators.
These pins are active low. The three indicator outputs have open
drains and are designed to be used with LEDs. Each output can
sink over 20mA, which requires the use of an external current
limiting resistor. The three indicator signals denote fast charge
stage, topping and maintenance stages, and the polling detect or
battery fault and out-of-temperature range modes as shown in
Table 1.
The charge mode (CMN) indicator is activated continuously during
the soft start and fast charge stages. The CMN indicator flashes at a
one-second rate when the
ICS1700A
is applying a topping or
maintenance charge.
The polling fault (PFN) indicator is on when the
ICS1700A
polls
for a battery for the first 10 seconds. The controller applies
periodic charge pulses to detect the presence of a battery. The
indicator is a warning that these charge pulses are appearing at the
charging system terminals at regular intervals. When a battery is
detected, the indicator is turned off. The indicator is also active if
the battery is removed from the system, warning that a fault has
occurred.
The out-of-temperature range (OTN) indicator is active whenever
the voltage at the temperature sense (THERM) input enters a range
that indicates that the attached battery is too hot to charge. The
OTN indicator is also activated with the CMN indicator if the
controller is initialized with the battery in the cold battery charge
region.
Pin Descriptions
The
ICS1700A
requires some external components to control the
clock rate, sense temperature and provide an indicator display. The
controller must be interfaced to an external power source that will
provide the current required to charge a battery pack and, if
desired, a circuit that will sink discharge current.
Output Logic Signals: CHG, DCHG Pins
The CHG and DCHG pins are active high, TTL compatible
outputs. In addition to being TTL compatible, the CMOS outputs
are capable of sourcing current which adds flexibility when
interfacing to other circuitry. A logic high on the CHG pin
indicates that the charging current supply should be activated. If
applicable, a logic high on the DCHG pin indicates that the
discharge circuit should be activated.
Care must be taken to control wiring resistance and inductance.
The load resistor must be capable of handling this short duration
high-amplitude pulse.
Table 1: Indicator Description List
PFN
On
CMN
OTN
Description
Polling mode or battery fault
Maintenance and topping charge
Fast charge
Hot battery shutdown
Cold battery charge
See Applications Information
See Applications Information
Flash
On
On
On
on
Flash
On
One flash
On
相關PDF資料
PDF描述
ICS1700AST QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries
ICS1708N IC REG LDO 1A 10V TO220FP
ICS1708S IC REG LDO 1A 10V SHDN TO220FP-5
ICS1708ST IC REG LDO 1A 10V TO220FP
ICS1708 QuickSaver Charge Control IC for Nickel-Cadmium and Nickel-Metal Hydride Batteries
相關代理商/技術參數
參數描述
ICS1700AST 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries
ICS1700M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management
ICS1700N 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management
ICS1702 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries
ICS1702M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*