- 您現在的位置：買賣IC網 > PDF目錄383093 > ICS1700AS (Electronic Theatre Controls, Inc.) QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries PDF資料下載
參數資料
| 型號： | ICS1700AS |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| 中文描述： | QuickSaver充電控制器的鎳鎘和鎳氫電池 |
| 文件頁數： | 7/24頁 |
| 文件大小： | 204K |
| 代理商： | ICS1700AS |
7
ICS1700A
Battery Fault Detection
The
ICS1700A
will turn on the PFN fault indicator and shut down
if the battery is removed or if an open circuit occurs in the current
path anytime after fast charge has been initiated. When in the
topping charge or maintenance charge stages, a charge pulse may
not occur for several seconds. During the period between charge
pulses, the voltage at VIN should be greater than 0.5V if a battery
is attached. If the voltage at VIN is less than 0.5V, the
ICS1700A
assumes the battery has been removed, a fault condition is
indicated by the PFN fault indicator, and the controller shuts down.
Cold Battery Charging
Cold battery charging is activated if a voltage at the THERM pin is
in the cold battery voltage range, as shown in Figure 7. The
ICS1700A
checks for a cold battery before initiating fast charge. If
a cold battery is present before fast charging begins, the
ICS1700A
begins a two-hour C/10 topping charge (the pulsed duty cycle is
based on the selected charge rate). If the battery is still cold after
the two-hour topping charge is complete, the
ICS1700A
begins a
C/40 maintenance charge. The maintenance charge will continue
for as long as the battery remains cold. The thermistor voltage at
the THERM pin is checked every second to see if the battery has
warmed up. If so, the
ICS1700A
stops the topping charge or
maintenance charge and begins a fast charge at a rate selected by
the SEL0 and SEL1 inputs. See the section on
Temperature
Sensing
for more information.
The CMN will flash at a one-second rate, and the OTN indicator
will be active, indicating that a low current charge is being applied
to a battery that is outside the specified temperature range for fast
charging.
Battery Polling
Upon power-up or after a reset is issued, any excess charge from
filter capacitors at the charging system terminals is removed with a
series of discharge pulses. After the discharge pulse series is
complete, the voltage at VIN must be greater than 0.5V when a
battery is present. If the voltage at VIN is less than 0.5V, the
ICS1700A
assumes no battery is attached and initiates a polling
sequence.
The
ICS1700A
then applies a 100ms charge pulse. During the
pulse, the
ICS1700A
monitors the VIN pin to determine if the
divided down terminal voltage is greater than the internal 2.0V
reference. If the battery is present, the voltage is clamped below the
2.0V reference when the current pulse is applied and the fast
charge stage begins immediately. If a battery is not present, the
voltage at VIN rises above the 2.0V reference and the PFN fault
indicator is activated.
The charge pulses repeat for 10 seconds. If the battery is installed
within 10 seconds, the
ICS1700A
will turn off the PFN fault
indicator and enter the soft start stage. If the battery is not installed
within 10 seconds, the PFN fault indicator remains active and the
ICS1700A
shuts down. A reset must be issued to restart the
controller after installing the battery.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS1700AST | QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| ICS1708N | IC REG LDO 1A 10V TO220FP |
| ICS1708S | IC REG LDO 1A 10V SHDN TO220FP-5 |
| ICS1708ST | IC REG LDO 1A 10V TO220FP |
| ICS1708 | QuickSaver Charge Control IC for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS1700AST | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| ICS1700M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| ICS1700N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| ICS1702 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
| ICS1702M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QuickSaver Charge Controller for Nickel-Cadmium and Nickel-Metal Hydride Batteries |
發布緊急采購，3分鐘左右您將得到回復。