參數資料
型號： ICM7242IPAZ
廠商： Intersil
文件頁數： 6/10頁
文件大?。?/td> 0K
描述： IC OSC BINARY CTC 13MHZ 8-DIP
標準包裝： 50
類型： 計數器/計時器電路（CTC），二進制
計數： 128/256
頻率： 0.1Hz ~ 13MHz
電源電壓： 2 V ~ 16 V
電流 - 電源： 340µA
工作溫度： -25°C ~ 85°C
封裝/外殼： 8-DIP（0.300"，7.62mm）
包裝： 管件
供應商設備封裝： 8-PDIP
安裝類型： 通孔
5
FN2866.4
February 9, 2007
To use the 8-bit counter without the timebase, Terminal 7
(RC) should be connected to ground and the outputs taken
from Terminals 2 and 3.
The ICM7242 may be used for a very low frequency square
wave reference. For this application the timing components
are more convenient than those that would be required by a
555 timer. For very low frequencies, devices may be
cascaded (see Figure 3).
For monostable operation the
÷28 output is connected to the
RESET terminal. A positive edge on TRIGGER initiates the
cycle (NOTE: TRIGGER overrides RESET).
The ICM7242 is superior in all respects to the 2242 except
for initial accuracy and oscillator stability. This is primarily
due to the fact that high value p-resistors have been used on
the ICM7242 to provide the comparator timing points.
By selection of R and C, a wide variety of sequence timing
can be realized. A typical flow chart for a machine tool
controller could be as shown in Figure 5.
By cascading devices, use of low cost CMOS AND/OR gates
and appropriate RC delays between stages, numerous
sequential control variations can be obtained. Typical
applications include injection molding machine controllers,
phonograph record production machines, automatic
sequencers (no metal contacts or moving parts), milling
machine controllers, process timers, automatic lubrication
systems, etc.
Sequence Timing
Process Control
Machine Automation
Electro-Pneumatic Drivers
Multi Operation (Serial or Parallel Controlling)
1
2
3
4
8
7
6
5
VDD
C
R
1
2
3
4
8
7
6
5
ICM7242
f = RC/216
FIGURE 3. LOW FREQUENCY REFERENCE (OSCILLATOR)
OUTPUT
TERMINAL 3
TB OUTPUT
TRIGGER
TERMINAL 8
TERMINAL 6
1
2
3
4
8
7
6
5
VDD
C
R
ICM7242
OUTPUT
100k
Ω
TRIGGER
RESET
S1
FIGURE 4. MONOSTABLE OPERATION
TABLE 1. COMPARING THE ICM7242 WITH THE 2242
CHARACTERISTICS
ICM7242
2242
Operating Voltage
2V to 16V
4V to 15V
Operating Temperature Range
-25°C to 85°C0°C to 70°C
Supply Current, VDD = 5V
0.7mA (Max)
7mA (Max)
Pullup Resistors
TB Output
No
Yes
÷2 Output
No
Yes
÷256 Output
No
Yes
Toggle Rate
3.0MHz
0.5MHz
Resistor to Inhibit Oscillator
No
Yes
Resistor in Series with Reset for
Monostable Operation
No
Yes
Capacitor TB Terminal for HF
Operation
No
Sometimes
TRIGGERING CAN BE
OBTAINED FROM A
PREVIOUS STAGE,
A LIMIT SWITCH,
OPERATOR SWITCH, ETC.
ENABLE
10s
WAIT
5s
START
ICM7242
WAIT
5s
COUNT
TO 185
ENABLE
5s
ICM7242
ICM7240
ICM7242
STOP
START
STOP
WAIT
5s
WAIT
5s
ENABLE
5s
COUNT
TO 185
ENABLE
10s
FIGURE 5. FLOW CHART FOR MACHINE TOOL CONTROLLER
-
ICM7242
相關PDF資料
PDF描述
MS17344R24C22P CONN PLUG 4POS STRAIGHT W/PINS
MC14536BDWG IC OSC PROG TIMER 2MHZ 16SOIC
MS17344C24C22P CONN PLUG 4POS STRAIGHT W/PINS
MS17344R24C28P CONN PLUG 24POS STRAIGHT W/PINS
VI-B1V-IU-F4 CONVERTER MOD DC/DC 5.8V 200W
相關代理商/技術參數
參數描述
ICM7242IWE 功能描述:計時器和支持產品 Programmable RC Timer/Counter RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel
ICM7242IWE+ 制造商:Maxim Integrated Products 功能描述:FIXED RC TIMER/COUNTER - Bulk
ICM7242IWE-T 功能描述:計時器和支持產品 Programmable RC Timer/Counter RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel
ICM7242MJA 功能描述:計時器和支持產品 RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel
ICM7242MJA.C00122 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*