參數資料
型號: ICM7226BIPL
廠商: INTERSIL CORP
元件分類: 計數器
英文描述: DISPLAY DRIVER COUNTER, PDIP40
封裝: PLASTIC, DIP-40
文件頁數: 3/19頁
文件大?。?/td> 556K
代理商: ICM7226BIPL
11
Overflow Indication
When overflow happens in any measurement it will be indicated
on the decimal point of the digit 8. A separate LED indicator can
be used. Figure 14 shows how to connect this indicator.
Time Interval Measurement
When in the time interval mode and measuring a single
event, the lCM7226A and lCM7226B must first be “primed”
prior to measuring the event of interest. This is done by first
generating a negative going edge on Channel A followed by a
negative going edge on Channel B to start the “measurement
interval”. The inputs are then primed ready for the measure-
ment. Positive going edges on A and B, before or after the
priming, will be needed to restore the original condition.
Priming can be easily accomplished using the circuit in
Figure 15.
Following the priming procedure (when in single event or 1
cycle range) the device is ready to measure one (only) event.
When timing repetitive signals, it is not necessary to “prime”
the lCM7226A and lCM7226B as the first alternating signal
states automatically prime the device. See Figure 1.
During any time interval measurement cycle, the ICM7226A
and lCM7226B requires 200ms following B going low to
update all internal logic. A new measurement cycle will not
take place until completion of this internal update time.
Oscillator Considerations
The oscillator is a high gain complementary FET inverter. An
external resistor of 10M
or 22M should be connected
between the oscillator input and output to provide biasing.
The oscillator is designed to work with a parallel resonant
10MHz quartz crystal with a static capacitance of 22pF and
a series resistance of less than 35
. Among suitable
crystals is the 10MHz CTS KNIGHTS ISI-002.
For a specific crystal and load capacitance, the required gM
canbecalculatedasfollows:
CO = Crystal Static Capacitance
RS = Crystal Series Resistance
CIN = Input Capacitance
COUT = Output Capacitance
ω =2πf
The required gM should not exceed 50% of the gM specified
for the lCM7226 to insure reliable startup. The OSCillator
INPUT and OUTPUT pins each contribute about 4pF to CIN
and COUT. For maximum stability of frequency, CIN and
COUT should be approximately twice the specified crystal
static capacitance.
In cases where non decade prescalers are used, it may be
desirable to use a crystal which is neither 10MHz or 1MHz.
In that case both the multiplex rate and time between
measurements will be different. The multiplex rate is:
for 10MHz mode and
for the
1MHz mode. The time between measurements is
in
the 10MHz mode and
in the 1MHz mode.
The buffered oscillator output should be used as an oscillator
test point or to drive additional logic; this output will drive one
low power Schottky TTL load. When the buffered oscillator
output is used to drive CMOS or the external oscillator input,
a10k
resistor should be added from the buffered oscillator
output to VDD.
The crystal and oscillator components should be located as
close to the chip as practical to minimize pickup from other
signals. Coupling from the EXTERNAL OSClLLATOR INPUT
to the OSClLLATOR OUTPUT or INPUT can cause
undesirable shifts in oscillator frequency.
a
b
c
d
f
g
e
DP
LED
overflow
indicator
connections: Overflow
will
be
indicated on the decimal point output of digit 8.
FIGURE 14. SEGMENT IDENTIFICATION AND DISPLAY FONT
DEVICE
CATHODE
ANODE
ICM7226A
Decimal Point
D8
ICM7226B
D8
Decimal Point
SIGNAL A
SIGNAL B
INPUT A
INPUT B
VDD
N.O.
100K
1N914
VDD
150K
1
0.1
F
10K
10nF
11
1
2
VSS
PRIME
FIGURE 15. PRIMING CIRCUIT, SIGNALS A AND B BOTH HIGH
OR LOW
DEVICE
TYPE
1
CD4049B Inverting Buffer
2
CD4070B Exclusive - OR
g
M
ω
2
C
IN COUT RS 1
C
O
C
L
--------
+
2
=
where C
L
C
IN COU T
C
IN
C
OUT
+
---------------------------------
=
f
MUX
f
OSC
210
4
×
-------------------
=
f
MUX
f
OSC
210
3
×
-------------------
=
210
6
×
f
OSC
-------------------
210
5
×
f
OSC
-------------------
ICM7226A, ICM7226B
相關PDF資料
PDF描述
ICS1493K-17LFT 48 MHz, PROC SPECIFIC CLOCK GENERATOR, QCC20
ICS1493K-17LF 48 MHz, PROC SPECIFIC CLOCK GENERATOR, QCC20
ICS1493K-17LFT 48 MHz, PROC SPECIFIC CLOCK GENERATOR, QCC20
ICS1522MLF 230 MHz, VIDEO CLOCK GENERATOR, PDSO24
ICS1524AMT 250 MHz, OTHER CLOCK GENERATOR, PDSO24
相關代理商/技術參數
參數描述
ICM7226BIPL WAF 制造商:Intersil Corporation 功能描述:
ICM7226BLPL 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Digit, Multi-Function, Frequency Counter/Timer
ICM7226D 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:TIMERS COUNTERS AND DISPLAY DRIVERS
ICM7227 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:N-CHANNEL JFET
ICM7227AIPI 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:TIMERS COUNTERS AND DISPLAY DRIVERS