- 您現在的位置：買賣IC網 > PDF目錄67684 > ICM7226BIPL (INTERSIL CORP) DISPLAY DRIVER COUNTER, PDIP40 PDF資料下載
參數資料
| 型號： | ICM7226BIPL |
| 廠商： | INTERSIL CORP |
| 元件分類： | 計數器 |
| 英文描述： | DISPLAY DRIVER COUNTER, PDIP40 |
| 封裝： | PLASTIC, DIP-40 |
| 文件頁數： | 2/19頁 |
| 文件大小： | 556K |
| 代理商： | ICM7226BIPL |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
10
RST IN Input
The RST IN is provided to reset the Main Counter, stop any
measurement in progress, and enable the display latches,
resulting in the all zero display. It is suggested to have a
capacitor at this input to VSS to prevent any hangup problem
on power up. See application circuits.
EXT RANGE Input
This input is provided to select ranges other than those
provided in the chip. In any mode of measurement the duration
of measurement is determined by the EXT RANGE if this input
is enabled. This input is sampled at 10ms intervals by the
100Hz reference derived from the timebase. Figure 12 shows
the relationship between this input, 100Hz reference signal and
MEAS IN PROGRESS. EXT RANGE can change state
anywhere during the period of 100Hz reference by will be
sampled at the trailing edge of the period to start or stop
measurement.
This input should not be used for short arbitrary ranges
(because of its sampling period), it is provided for very long
gating purposes. A way of using the ICM7226 for a short
arbitrary range is to feed the gating signal into the INPUT B
and run the device in the Frequency Ratio mode. Note that
the gating period will be from one positive edge until the next
positive edge of INPUT B (0.01s/1 cycle range).
MEAS IN PROGRESS,STORE, RST OUT Outputs
These outputs are provided for external system interfacing.
MEAS IN PROGRESS stays low during measurements and
goes high for intervals between measurements. Figure 13
shows the relationship between these outputs for intervals
between measurements. All these outputs can drive a low
power Schottky TTL. The MEAS IN PROGRESS can drive
one ECL load if the ECL device is powered from the same
power supply as the ICM7226.
BCD Outputs
The BCD representation of each display digit is available at
the BCD outputs in a multiplexed fashion. See Table 3 for dig-
its truth table. The BCD output of each digit is available when
its corresponding digit output is activated. Note that the digit
outputs are multiplexed from D8 (MSD) to D1 (LSD). The pos-
itive going (ICM7226A, common anode) or the negative going
(ICM7226B, common cathode) digit drive signals lag the BCD
data by 2
sto 6s. This starting edge of each digit drive sig-
nal shouldbeusedtoexternally latchthe BCD data. Each
BCD output drives one low power Schottky TTL load. Leading
zero blanking has no effect on the BCD outputs.
BUF OSC OUT Output
The BUFFered OSCillator OUTput is provided for use of the
on-board oscillator signal, without loading the oscillator itself.
This output can drive one low power Schottky TTL load. Care
should be taken to minimize capacitive loading on this pin.
Decimal Point Position
Table 4 shows the decimal point position for different modes
of lCM7226 operation. Note that the digit 1 is the least signif-
icant digit. Table is given for 10MHz timebase frequency.
REFERENCE
COUNTER
CLOCK
MEAS
IN PROGRESS
EXT RANGE
INPUT
tr
FIGURE 12. EXTERNAL RANGE INPUT TO END OF
MEASUREMENT IN PROGRESS
TABLE 3. TRUTH TABLE BCD OUTPUTS
NUMBER
BCD 8
PIN 7
BCD 4
PIN 6
BCD 2
PIN 17
BCD 1
PIN 18
00000
10001
20010
30011
40100
50101
60110
70111
81000
91001
40ms
STORE
RESET OUT
60ms
30ms TO
40ms
190ms TO 200ms
MEAS
IN PROGRESS
FIGURE 13. RESET OUT, STORE AND MEASUREMENT IN
PROGRESS OUTPUTS BETWEEN MEASUREMENTS
TABLE 4. DECIMAL POINT POSITIONS
RANGE
FREQUENCY
PERIOD
FREQUENCY
RATIO
TIME
INTERVAL
UNIT
COUNTER
OSCILLATOR
FREQUENCY
0.01s/1 Cycle
D2
D1
D2
D1
D2
0.1s/10 Cycle
D3
D2
D3
D1
D3
1s/100 Cycle
D4D4D3D4D1D4
10s/1K Cycle
D5D5D4D5D1D5
External
N/A
ICM7226A, ICM7226B
相關PDF資料 |
PDF描述 |
|---|---|
| ICS1493K-17LFT | 48 MHz, PROC SPECIFIC CLOCK GENERATOR, QCC20 |
| ICS1493K-17LF | 48 MHz, PROC SPECIFIC CLOCK GENERATOR, QCC20 |
| ICS1493K-17LFT | 48 MHz, PROC SPECIFIC CLOCK GENERATOR, QCC20 |
| ICS1522MLF | 230 MHz, VIDEO CLOCK GENERATOR, PDSO24 |
| ICS1524AMT | 250 MHz, OTHER CLOCK GENERATOR, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICM7226BIPL WAF | 制造商:Intersil Corporation 功能描述: |
| ICM7226BLPL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226D | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:TIMERS COUNTERS AND DISPLAY DRIVERS |
| ICM7227 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:N-CHANNEL JFET |
| ICM7227AIPI | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:TIMERS COUNTERS AND DISPLAY DRIVERS |
發布緊急采購，3分鐘左右您將得到回復。