參數資料
型號： ICE3A1065L
廠商： INFINEON TECHNOLOGIES AG
英文描述： Off-Line SMPS Current Mode Controller with integrated 650V Startup Cell/Depletion CoolMOS⑩ and Latched off Mode
中文描述： 離線式開關電源電流模式控制器，集成了?650V啟動細胞/消耗的CoolMOS⑩和鎖存關閉模式
文件頁數： 7/28頁
文件大小： 525K
代理商： ICE3A1065L
3
Version 2.0
7
8 May 2006
CoolSET-F3
ICE3xxx65L
Functional Description
Functional Description
All values which are used in the functional description
are typical values. For calculating the worst cases the
min/max values which can be found in section 4
Electrical Characteristics have to be considered.
3.1
Introduction
CoolSET-F3 is the further development of the
CoolSET-F2 to meet the requirements for the lowest
Standby Power at minimum load and no load
conditions. A new fully integrated Standby Power
concept is implemented into the IC in order to keep the
application design easy. Compared to CoolSET-F2
no further external parts are needed to achieve the
lowest Standby Power. An intelligent Active Burst
Mode is used for this Standby Mode. After entering this
mode there is still a full control of the power conversion
by the secondary side via the same optocoupler that is
used for the normal PWM control. The response on
load jumps is optimized. The voltage ripple on V
out
is
minimized. V
out
is further on well controlled in this
mode.
The usually external connected RC-filter in the
feedback line after the optocoupler is integrated in the
IC to reduce the external part count.
Furthermore a high voltage Startup Cell is integrated
into the IC which is switched off once the Undervoltage
Lockout on-threshold of 15V is exceeded. This Startup
Cell is part of the integrated Depl. CoolMOS. The
external startup resistor is no longer necessary as this
Startup Cell is connected to the Drain. Power losses
are therefore reduced. This increases the efficiency
under light load conditions drastically.
The Soft-Start capacitor is also used for providing an
adjustable blanking window for high load jumps.
During this time window the overload detection is
disabled. With this concept no further external
components are necessary to adjust the blanking
window.
In order to increase the robustness and safety of the
system, the IC provides 2 levels of protection modes:
Latched Off Mode and Auto Restart Mode. The
Latched Off Mode is only entered under dangerous
conditions which can damage the SMPS if not
switched off immediately. A restart of the system can
only be done by disconnecting the AC line.
The Auto Restart Mode reduces the average power
conversion to a minimum under unsafe operating
conditions. This is necessary for a prolonged fault
condition which could otherwise lead to a destruction
of the SMPS over time. Once the malfunction is
removed, normal operation is automatically initiated
after the next Start Up Phase.
The internal precise peak current limitation reduces the
costs for the transformer and the secondary diode. The
influence of the change in the input voltage on the
power limitation can be avoided together with the
integrated
Propagation
Therefore the maximum power is nearly independent
on the input voltage which is required for wide range
SMPS. There is no need for an extra over-sizing of the
SMPS, e.g. the transformer or the secondary diode.
Delay
Compensation.
3.2
Power Management
Figure 3
Power Management
The Undervoltage Lockout monitors the external
supply voltage V
VCC
. When the SMPS is plugged to the
main line the internal Startup Cell is biased and starts
to charge the external capacitor C
VCC
which is
connected to the VCC pin. This VCC charge current
which is provided by the Startup Cell from the Drain pin
is 1.05mA. When V
VCC
exceeds the on-threshold
V
CCon
=15V the internal voltage reference and bias
circuit are switched on. Then the Startup Cell is
switched off by the Undervoltage Lockout and
therefore no power losses present due to the
connection of the Startup Cell to the Drain voltage. To
avoid uncontrolled ringing at switch-on a hysteresis is
implemented. The switch-off of the controller can only
take place after Active Mode was entered and V
VCC
falls below 8.5V.
Internal Bias
Voltage
Reference
Power Management
Latched Off Mode
Reset
V
VCC
< 6V
6.5V
Latched Off
Mode
Undervoltage Lockout
15V
8.5V
T1
Power-Down Reset
SoftS
Active Burst
Mode
Auto Restart
Mode
Startup Cell
VCC
Drain
Depl. CoolMOS
相關PDF資料
PDF描述
ICE3B0365L Off-Line SMPS Current Mode Controller with integrated 650V Startup Cell/Depletion CoolMOS⑩ and Latched off Mode
ICE3A1565L Off-Line SMPS Current Mode Controller with integrated 650V Startup Cell/Depletion CoolMOS⑩ and Latched off Mode
ICE3A2565 Off-Line SMPS Current Mode Controller with integrated 650V Startup Cell/CoolMOS
ICE3A3065I Off-Line SMPS Current Mode Controller with integrated 650V Startup Cell/CoolMOS
ICE3A3065P Off-Line SMPS Current Mode Controller with integrated 650V Startup Cell/CoolMOS
相關代理商/技術參數
參數描述
ICE3A1065LJ 功能描述:電流型 PWM 控制器 CoolSET F3 650V RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
ICE3A1065LJHKLA1 制造商:Infineon Technologies AG 功能描述:Current Mode PWM Controller 650V 1A 8-Pin PDIP 制造商:Infineon Technologies AG 功能描述:IC OFFLINE CTRLR SMPS OTP 8DIP
ICE3A1065LXK 制造商:Infineon Technologies AG 功能描述:Current Mode PWM Controller 8-Pin PDIP
ICE3A1065XK 制造商:Infineon Technologies AG 功能描述:Current Mode PWM Controller 650V 1A 8-Pin PDIP
ICE3A1565 功能描述:電流型 PWM 控制器 Off-Line SMPS Currnt Mode CTRLR 650V RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*