- 您現在的位置：買賣IC網 > PDF目錄67681 > HPMX-2003T10 (AGILENT TECHNOLOGIES INC) 800 MHz - 1000 MHz RF/MICROWAVE VECTOR MODULATOR PDF資料下載
參數資料
| 型號： | HPMX-2003T10 |
| 廠商： | AGILENT TECHNOLOGIES INC |
| 元件分類： | 調制器/解調器 |
| 英文描述： | 800 MHz - 1000 MHz RF/MICROWAVE VECTOR MODULATOR |
| 文件頁數： | 11/16頁 |
| 文件大小： | 188K |
| 代理商： | HPMX-2003T10 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁
4
HPMX-2003 Typical Data
Measurement
Direct measurement of the ampli-
tude and phase error at the output
is an accurate way to evaluate
modulator performance. By mea-
suring the error directly, all the
harmonics, LO leakage, etc. that
show up in the output signal are
accounted for. Figure 3, below,
shows the test setup that was used
to create the amplitude and phase
error plots (figures 12 and 13).
Amplitude and phase error are
measured by using the four chan-
nel power supply to simulate I and
Q input signals. Real 2.5 Vp-p I and
Q signals would swing 1.25 volts
above and below an average 2.5 V
level, therefore, a “high” level in-
put is simulated by applying
3.75 V, and a “l(fā)ow” level by apply-
ing 1.25 V to the I and/or Q inputs.
bling phase readings on the net-
work analyzer.
The same test setup shown below
is used to measure input and out-
put VSWR, reverse isolation, and
power vs. frequency. VImod and
VQmod are set to 3.75 V and the
appropriate frequency ranges are
swept. S11 provides input VSWR
data, S22 provides output VSWR
data. S21 provides power output
(add source power to S21 derived
gain).
LO leakage data shown in figures
18, and 19 is generated by setting
VImod = VQmod = VIref = VQref = 2.5 V
then performing an S21 sweep.
Since phase is not important for
these measurements, a scalar net-
work analyzer or a signal genera-
tor and spectrum analyzer could
be used.
Amplitude and phase are
measured by setting the network
analyzer for an S21 measurement
at frequency of choice. Set the
port 1 stimulus level to the LO
level you intend to use in your cir-
cuit (-12 dBm for the data sheet).
A 6-10 dB attenuator can be
placed in the line to port 2 to pre-
vent network analyzer overload,
depending upon the network ana-
lyzer you are using.
By adjusting the VImod and VQmod
settings you can step around the
I, Q vector circle, reading mag-
nitude and phase at each point.
The relative values of phase and
amplitude at the various points
will indicate the accuracy of the
modulator. Note: you must use
very low ripple power supplies
for the reference, VImod, and VQmod
supplies. Ripple or noise of only a
few millivolts will appear as wob-
Figure 3. Test Setup for Measuring Amplitude and Phase Error, Input and Output
VSWR, Power Output and LO Leakage of the Modulator.
HP-6626A
SYSTEM DC POWER SUPPLY
(FOUR OUTPUTS)
5 V
VQmod
VImod
2.5 V
HP-8753C VECTOR NETWORK ANALYZER
PORT 1
PORT 2
LO
Q
R
VCC
5 V
OUT
R
C
H
VER 1
I
HPMX-2003/5
C
相關PDF資料 |
PDF描述 |
|---|---|
| HPMX-2005T10 | 25 MHz - 250 MHz RF/MICROWAVE VECTOR MODULATOR |
| HPMX-2005 | 50 MHz - 200 MHz RF/MICROWAVE VECTOR MODULATOR |
| HPMX-5001 | 1500 MHz - 2500 MHz RF/MICROWAVE UP/DOWN CONVERTER, 2 dBm OUTPUT POWER-MAX |
| HPMX-5001 | 1500 MHz - 2500 MHz RF/MICROWAVE UP/DOWN CONVERTER, 2 dBm OUTPUT POWER-MAX |
| HPMX-7102-BLK | RF/MICROWAVE DOWN CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HPMX-2005 | 制造商:Hewlett Packard Co 功能描述:25 MHz - 250 MHz RF/MICROWAVE VECTOR MODULATOR |
| HPMX-2005_1 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:Silicon Bipolar RFIC 100 MHz Vector Modulator |
| HPMX-2006 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:0.8 - 2.5 GHz Upconverter/Amplifier |
| HPMX-2006-BLK | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:0.8 - 2.5 GHz Upconverter/Amplifier |
| HPMX-2006-TR1 | 制造商:AGILENT 制造商全稱:AGILENT 功能描述:0.8 - 2.5 GHz Upconverter/Amplifier |
發布緊急采購，3分鐘左右您將得到回復。