- 您現在的位置：買賣IC網 > PDF目錄371881 > HPC467064EL20 (NATIONAL SEMICONDUCTOR CORP) High-Performance microController with a 16k UV Erasable CMOS EPROM PDF資料下載
參數資料
| 型號： | HPC467064EL20 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | High-Performance microController with a 16k UV Erasable CMOS EPROM |
| 中文描述： | UVPROM, MICROCONTROLLER, CQCC68 |
| 封裝： | WINDOWED, LDCC-68 |
| 文件頁數： | 16/34頁 |
| 文件大小： | 415K |
| 代理商： | HPC467064EL20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
HPC167064 Operating Modes
SINGLE CHIP NORMAL MODE
In this mode, the HPC167064 functions as a self-contained
microcomputer (see Figure 15) with all memory (RAM and
EPROM) on-chip. It can address internal memory only, con-
sisting of 16 kbytes of EPROM (C000 to FFFF) and
512 bytes of on-chip RAM and Registers (0000 to 02FF).
The ‘‘illegal address detection’’ feature of the WATCHDOG
is enabled in the Single-Chip Normal mode and a WATCH-
DOG Output (WO) will occur if an attempt is made to access
addresses that are outside of the on-chip EPROM and RAM
range of the device. Ports A and B are used for I/O func-
tions and not for addressing external memory. The EXM pin
and the EA bit of the PSW register must both be logic ‘‘0’’ to
enter the Single-Chip Normal mode.
EXPANDED NORMAL MODE
The Expanded Normal mode of operation enables the
HPC167064 to address external memory in addition to the
on-chip ROM and RAM (see Table I). WATCHDOG illegal
address detection is disabled and memory accesses may
be made anywhere in the 64 kbyte address range without
triggering an illegal address condition. The Expanded Nor-
mal mode is entered with the EXM pin pulled low (logic ‘‘0’’)
and setting the EA bit in the PSW register to ‘‘1’’.
TABLE I. HPC167064 Operating Modes
Operating Mode
EXM
Pin
EA
Bit
Memory
Configuration
Single-Chip Normal
0
0
C000–FFFF On-Chip
Expanded Normal
0
1
C000–FFFF On-Chip
0300–BFFF Off-Chip
Single-Chip ROMless
1
0
C000–FFFF Off-Chip
Expanded ROMless
1
1
0300–FFFF Off-Chip
SINGLE-CHIP ROMless MODE
In this mode, the on-chip EPROM of the HPC167064 is not
used. The address space corresponding to the on-chip
EPROM is mapped into external memory so 16k of external
memory may be used with the HPC167064 (see Table I).
The WATCHDOG circuitry detects illegal addresses (ad-
dresses not within the on-chip EPROM and RAM range).
The Single-Chip ROMless mode is entered when the EXM
pin is pulled high (logic ‘‘1’’) and the EA bit is logic ‘‘0’’.
EXPANDED ROM MODE
This mode of operation is similar to Single-Chip ROMless
mode in that no on-chip ROM is used, however, a full
64 kbytes of external memory may be used. The ‘‘illegal
address detection’’ feature of WATCHDOG is disabled. The
EXM pin must be pulled high (logic ‘‘1’’) and the EA bit in the
PSW register set to ‘‘1’’ to enter this mode.
Wait States
The internal EPROM can be accessed at the maximum op-
erating frequency with one wait state. With 0 wait states,
internal ROM accesses are limited to
)/3
f
C
max. The
HPC167064 provides four software selectable Wait States
that allow access to slower memories. The Wait States are
selected by the state of two bits in the PSW register. Addi-
tionally, the RDY input may be used to extend the instruc-
tion cycle, allowing the user to interface with slow memories
and peripherals.
TL/DD/11046–23
FIGURE 15. Single-Chip Mode
Power Save Modes
Two power saving modes are available on the HPC167064:
HALT and IDLE. In the HALT mode, all processor activities
are stopped. In the IDLE mode, the on-board oscillator and
timer T0 are active but all other processor activities are
stopped. In either mode, all on-board RAM, registers and
I/O are unaffected.
HALT MODE
The HPC167064 is placed in the HALT mode under soft-
ware control by setting bits in the PSW. All processor activi-
ties, including the clock and timers, are stopped. In the
HALT mode, power requirements for the HPC167064 are
minimal and the applied voltage (V
CC
) may be decreased
without altering the state of the machine. There are two
ways of exiting the HALT mode: via the RESET or the NMI.
The RESET input reinitializes the processor. Use of the NMI
input will generate a vectored interrupt and resume opera-
tion from that point with no initialization. The HALT mode
can be enabled or disabled by means of a control register
HALT enable. To prevent accidental use of the HALT mode
the HALT enable register can be modified only once.
IDLE MODE
The HPC167064 is placed in the IDLE mode through the
PSW. In this mode, all processor activity, except the on-
board oscillator and Timer T0, is stopped. As with the HALT
mode, the processor is returned to full operation by the
RESET or NMI inputs, but without waiting for oscillator stabi-
lization. A timer T0 overflow will also cause the HPC167064
to resume normal operation.
Note:
If an NMI interrupt is received during the instruction which puts the
device in Halt or Idle Mode, the device will enter that power saving
mode. The interrupt will be held pending until the device exits that
power saving mode. When exiting Idle mode via the T0 overflow, the
NMI interrupt will be serviced when the device exits Idle. If another
NMI interrupt is received during either Halt of Idle the processor will
exit the power saving mode and vector to the interrupt address.
HPC167064 Interrupts
Complex interrupt handling is easily accomplished by the
HPC167064’s vectored interrupt scheme. There are eight
possible interrupt sources as shown in Table II.
16
相關PDF資料 |
PDF描述 |
|---|---|
| HPCL7800 | High CMR Isolation Amplifiers |
| HPC | |
| HPE2411C | Peripheral Miscellaneous |
| HPF240D20 | |
| HPF240D30 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HPC4844AE | 制造商:HEWLETT PACKARD 功能描述:INK CARTRIDGE C4844AE BLK 制造商:HEWLETT PACKARD 功能描述:INK CARTRIDGE, C4844AE, BLK |
| HPC4C100K | 功能描述:陶瓷復合電阻器 4W 10 ohm 10% RoHS:否 制造商:KOA Speer 電阻:1 kOhms 容差:10 % 功率額定值:1 W 電壓額定值:500 V 系列:PCF 溫度系數:- 1200 PPM / K 端接類型:Axial 尺寸:5.5 mm Dia. x 16.5 mm L 工作溫度范圍:- 40 C to + 200 C 封裝:Reel |
| HPC4C101K | 功能描述:陶瓷復合電阻器 4W 100 ohm 10% RoHS:否 制造商:KOA Speer 電阻:1 kOhms 容差:10 % 功率額定值:1 W 電壓額定值:500 V 系列:PCF 溫度系數:- 1200 PPM / K 端接類型:Axial 尺寸:5.5 mm Dia. x 16.5 mm L 工作溫度范圍:- 40 C to + 200 C 封裝:Reel |
| HPC4C102K | 功能描述:陶瓷復合電阻器 4W 1K ohm 10% RoHS:否 制造商:KOA Speer 電阻:1 kOhms 容差:10 % 功率額定值:1 W 電壓額定值:500 V 系列:PCF 溫度系數:- 1200 PPM / K 端接類型:Axial 尺寸:5.5 mm Dia. x 16.5 mm L 工作溫度范圍:- 40 C to + 200 C 封裝:Reel |
| HPC4C103K | 功能描述:陶瓷復合電阻器 4W 10K ohm 10% RoHS:否 制造商:KOA Speer 電阻:1 kOhms 容差:10 % 功率額定值:1 W 電壓額定值:500 V 系列:PCF 溫度系數:- 1200 PPM / K 端接類型:Axial 尺寸:5.5 mm Dia. x 16.5 mm L 工作溫度范圍:- 40 C to + 200 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。