- 您現在的位置：買賣IC網 > PDF目錄371881 > HPC16003 (National Semiconductor Corporation) High-Performance microControllers PDF資料下載
參數資料
| 型號： | HPC16003 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | High-Performance microControllers |
| 中文描述： | 高性能微控制器 |
| 文件頁數： | 18/36頁 |
| 文件大?。?/td> | 467K |
| 代理商： | HPC16003 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
HPC16003 Operating Modes
(Continued)
TL/DD/8801–19
FIGURE 17. 16-Bit External Memory
Wait States
The internal ROM can be accessed at the maximum operat-
ing frequency with one wait state. With 0 wait states, internal
ROM accesses are limited to
)/3
f
C
max.
The HPC16083 provides four software selectable Wait
States that allow access to slower memories. The Wait
States are selected by the state of two bits in the PSW
register. Additionally, the RDY input may be used to extend
the instruction cycle, allowing the user to interface with slow
memories and peripherals.
Power Save Modes
Two power saving modes are available on the HPC16083:
HALT and IDLE. In the HALT mode, all processor activities
are stopped. In the IDLE mode, the on-board oscillator and
timer T0 are active but all other processor activities are
stopped. In either mode, all on-board RAM, registers and
I/O are unaffected.
HALT MODE
The HPC16083 is placed in the HALT mode under software
control by setting bits in the PSW. All processor activities,
including the clock and timers, are stopped. In the HALT
mode, power requirements for the HPC16083 are minimal
and the applied voltage (V
CC
) may be decreased without
altering the state of the machine. There are two ways of
exiting the HALT mode: via the RESET or the NMI. The
RESET input reinitializes the processor. Use of the NMI in-
put will generate a vectored interrupt and resume operation
from that point with no initialization. The HALT mode can be
enabled or disabled by means of a control register HALT
enable. To prevent accidental use of the HALT mode the
HALT enable register can be modified only once.
IDLE MODE
The HPC16083 is placed in the IDLE mode through the
PSW. In this mode, all processor activity, except the on-
board oscillator and Timer T0, is stopped. As with the HALT
mode, the processor is returned to full operation by the
RESET or NMI inputs, but without waiting for oscillator stabi-
lization. A timer T0 overflow will also cause the HPC16083
to resume normal operation.
HPC16083 Interrupts
Complex interrupt handling is easily accomplished by the
HPC16083’s vectored interrupt scheme. There are eight
possible interrupt sources as shown in Table III.
TABLE III. Interrupts
Vector
Address
Interrupt
Source
Arbitration
Ranking
FFFF:FFFE
RESET
0
FFFD:FFFC
Nonmaskable external on
rising edge of I1 pin
1
FFFB:FFFA
External interrupt on I2 pin
2
FFF9:FFF8
External interrupt on I3 pin
3
FFF7:FFF6
External interrupt on I4 pin
4
FFF5:FFF4
Overflow on internal timers
5
FFF3:FFF2
Internal on the UART
transmit/receive complete
or external on EXUI
6
FFF1:FFF0
External interrupt on EI pin
7
18
相關PDF資料 |
PDF描述 |
|---|---|
| HPC16083 | High-Performance microControllers |
| HPC26003 | High-Performance microControllers |
| HPC16004 | High-Performance microController |
| HPC16064 | High-Performance microController |
| HPC26004 | High-Performance microController |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HPC16003E20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
| HPC16003EL20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
| HPC16003EL30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
| HPC16003L20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
| HPC16003L30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。