參數資料
型號： HMC714LP5E
廠商： HITTITE MICROWAVE CORP
元件分類： 檢測器
英文描述： 100 MHz - 5800 MHz RF/MICROWAVE LINEAR DETECTOR, 15 dBm INPUT POWER-MAX
封裝： 5 X 5 MM, ROHS COMPLIANT, PLASTIC, SMT, 32 PIN
文件頁數： 35/40頁
文件大?。?/td> 1985K
代理商： HMC714LP5E
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
P
O
W
E
R
D
E
T
E
C
T
O
R
S
-
SM
T
12
12 - 165
Due to part-to-part variations in log-slope and log-intercept, a system-level calibration is recommended to satisfy
absolute accuracy requirements. When performing this calibration, choose at least two test points: near the top-end
and bottom-end of the measurement range. It is best to measure the calibration points in the regions (of frequency and
amplitude) where accuracy is most important. Derive the log-slope and log-intercept, and store them in non-volatile
memory. Calibrate iPAR scaling by measuring the peak-to-average ratio of a known signal.
For example if the following two calibration points were measured at 2.35 GHz:
With Vrms = 2.34V at Pin = -7dBm,
and Vrms=1.84V at Pin = -16dBm
Slope Calibration Constant = SCC
SCC = (-16+7)/(1.84-2.34) = 18 dB/V
Intercept Calibration Constant = ICC
ICC = Pin – SCC*Vrms = -7 – 18.0 * 2.34 = -49.12dBm
Now performing a power measurement:
Vrms measures 2.13V
[Measured Pin] = [Measured Vrms]*SCC + ICC
[Measured Pin] = 2.13*18.0 – 49.12 = -10.78dBm
An error of only 0.22dB
Factory system calibration measurements should be made using an input signal representative of the application. If
the power detector will operate over a wide range of frequencies, choose a central frequency for calibration.
Layout Considerations
Mount RF input coupling capacitors close to the IN+ and IN- pins.
Solder the heat slug on the package underside to a grounded island which can draw heat away from the die
with low thermal impedance. The grounded island should be at RF ground potential.
Connect power detector ground to the RF ground plane, and mount the supply decoupling capacitors close
to the supply pins.
Definitions:
Log-slope: slope of PIN –> VRMS transfer characteristic. In units of mV/dB
Log-intercept: x-axis intercept of PIN –> VRMS transfer characteristic. In units of dBm.
RMS Output Error: The difference between the measured PIN and actual PIN using a line of best fit.
[measured_PIN] = [measured_VRMS] / [best-fit-slope] + [best-fit-intercept], dBm
Input Dynamic Range: the range of average input power for which there is a corresponding RMS output
voltage with “RMS Output Error” falling within a specific error tolerance.
Crest Factor: Peak power to average power ratio for time-varying signals.
System Calibration
HMC714LP5 / 714LP5E
v07.1109
DUAL RMS POWER DETECTOR
0.1 - 5.8 GHz
相關PDF資料
PDF描述
HMC742LP5 70 MHz - 4000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER
HMC770LP4BE 40 MHz - 1000 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER
HMC789ST89E 700 MHz - 2800 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER
HMC815LC5 21000 MHz - 27000 MHz RF/MICROWAVE UP CONVERTER
HMC909LP4E 0 MHz - 5800 MHz RF/MICROWAVE LINEAR DETECTOR, 10 dBm INPUT POWER-MAX
相關代理商/技術參數
參數描述
HMC7150LP3DE 功能描述:RF Modulator IC 16-VFQFN Exposed Pad 制造商:analog devices inc. 系列:- 包裝:剪帶 零件狀態:有效 功能:- LO 頻率:- RF 頻率:- P1dB:- 本底噪聲:* 輸出功率:- 電流 - 電源:- 電壓 - 電源:6V 測試頻率:- 封裝/外殼:16-VFQFN 裸露焊盤 標準包裝:1
HMC715LP3 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 2.1 - 2.9 GHz
HMC715LP3E 制造商:Hittite Microwave Corp 功能描述:IC MMIC AMP LNA PHEMT 16-QFN
HMC716LP3 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 3.1 - 3.9 GHz
HMC716LP3E 制造商:Hittite Microwave Corp 功能描述:IC MMIC AMP LNA PHEMT 16-QFN
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*