- 您現在的位置：買賣IC網 > PDF目錄174501 > HK16083N9S-T (TAIYO YUDEN CO LTD) 1 ELEMENT, 0.0039 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD PDF資料下載
參數資料
| 型號： | HK16083N9S-T |
| 廠商： | TAIYO YUDEN CO LTD |
| 元件分類： | 通用定值電感 |
| 英文描述： | 1 ELEMENT, 0.0039 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| 封裝： | CHIP, 1608 |
| 文件頁數： | 10/19頁 |
| 文件大?。?/td> | 1023K |
| 代理商： | HK16083N9S-T |
PRECAUTIONS
FERRITE
PRODUCTS
5
265
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
Technical considerations
Stages
Precautions
6/7
2. Cleaning conditions should be determined after
verifying, through a test run, that the cleaning pro-
cess does not affect the inductor's characteristics.
2. Inappropriate cleaning conditions insufcient or excessive cleaning may
detrimentally affect the performance of the inductors.
1 Excessive cleaning
In the case of ultrasonic cleaning, too much power output can cause
excessive vibration of the PC board which may lead to the cracking of
the inductor or the soldered portion, or decrease the terminal electrodes'
strength. Thus the following conditions should be carefully checked;
Ultrasonic output
Below 20 w/
Ultrasonic frequency
Below 40 kHz
Ultrasonic washing period 5 min. or less
5.Cleaning
7. Handling
Breakaway PC boards splitting along perforations
1. When splitting the PC board after mounting inductors
and other components, care is required so as not to
give any stresses of deection or twisting to the board.
2. Board separation should not be done manually, but by
using the appropriate devices.
General handling precautions
1. Always wear static control bands to protect against ESD.
2. Keep the inductors away from all magnets and mag-
netic objects.
3. Use non-magnetic tweezers when handling inductors.
4. Any devices used with the inductors soldering irons,
measuring instruments should be properly grounded.
5. Keep bare hands and metal products i.e., metal desk
away from chip electrodes or conductive areas that
lead to chip electrodes.
6. Keep inductors away from items that generate mag-
netic elds such as speakers or coils.
Mechanical considerations
1. Be careful not to subject the inductors to excessive
mechanical shocks.
1 If inductors are dropped on the oor or a hard surface
they should not be used.
2 When handling the mounted boards, be careful that
the mounted components do not come in contact with
or bump against other boards or components.
Application of resin coatings, moldings, etc. to the
PCB and components.
1. With some type of resins a decomposition gas or
chemical reaction vapor may remain inside the res-
in during the hardening period or while left under
normal storage conditions resulting in the deterio-
ration of the inductor's performance.
2. When a resin's hardening temperature is higher
than the inductor's operating temperature, the
stresses generated by the excess heat may lead to
inductor damage or destruction.
3. Stress caused by a resin s temperature generated
expansion and contraction may damage inductors.
The use of such resins, molding materials etc. is not
recommended.
6. Post cleaning processes
Precautions on the use of Multilayer chip Inductors, Multilayer chip inductors for high frequency, Multilayer ferrite chip beads
相關PDF資料 |
PDF描述 |
|---|---|
| HK16082N2S-T | 1 ELEMENT, 0.0022 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| HK160812NJ-T | 1 ELEMENT, 0.012 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| HK10058N2J-T | 1 ELEMENT, 0.0082 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| HK100582NJ-T | 1 ELEMENT, 0.082 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| HK10056N8J-T | 1 ELEMENT, 0.0068 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HK-1608-3N9STK | 功能描述:固定電感器 3.9nH 300mA 0.3nH RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| HK160847NH-T | 功能描述:固定電感器 INDCTR HIFREQ MLTLYR 0603 47nH 3% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| HK160847NJ-T | 功能描述:固定電感器 INDCTR HIFREQ MLTLYR 0603 47nH 5% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| HK-1608-47NJTK | 功能描述:固定電感器 47nH 300mA 5% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| HK160847NJ-TV | 功能描述:47nH Unshielded Multilayer Inductor 210mA 700 mOhm Max 0603 (1608 Metric) 制造商:taiyo yuden 系列:HK 包裝:剪切帶（CT） 零件狀態:過期 類型:多層 材料 - 磁芯:鐵氧體 電感:47nH 容差:±5% 額定電流:210mA 電流 - 飽和值:- 屏蔽:無屏蔽 DC 電阻（DCR）:700 毫歐最大 不同頻率時的 Q 值:12 @ 100MHz 頻率 - 自諧振:900MHz 等級:AEC-Q200 工作溫度:-40°C ~ 125°C 頻率 - 測試:100MHz 安裝類型:表面貼裝 封裝/外殼:0603（1608 公制） 大小/尺寸:0.063" 長 x 0.031" 寬（1.60mm x 0.80mm） 高度 - 安裝（最大值）:0.037"（0.95mm） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。