- 您現在的位置：買賣IC網 > Datasheet目錄40 > HIP1020CK-T (Intersil)IC CTRLR HOT PLUG SOT23-5 Datasheet資料下載
參數資料
| 型號： | HIP1020CK-T |
| 廠商： | Intersil |
| 文件頁數： | 4/6頁 |
| 文件大小： | 331K |
| 描述： | IC CTRLR HOT PLUG SOT23-5 |
| 標準包裝： | 3,000 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 5V，12V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SC-74A，SOT-753 |
| 供應商設備封裝： | SOT-23-5 |
| 包裝： | 帶卷 (TR) |
4
Application Information
The HIP1020 was designed specifically to address the
requirements of Device Bay peripherals. The small package,
low cost and integrated features make it the ideal component
for high-side power control of all three Device-Bay rail
voltages without using any additional components except for
the switching MOSFETs themselves. The integrated charge
pump supplies sufficient voltage to fully enhance the lower-
cost N-Channel power MOSFETs, and the internally-
controlled turn-on ramp provides soft switching for all types
of loads.
Although the HIP1020 was developed with Device Bay in
mind, it has the versatility to perform in any situation where
low-cost load switching is required.
MOSFET Selection for Device Bay Peripherals
When selecting power MOSFETs for Device Bay (or any
similar application), two major concerns are the voltage drop
across the MOSFET and the thermal requirements imposed
by the particular application. Voltage drop across the
MOSFET is controlled by its on-state resistance, r
DS(ON)
,
and the peak current through the device, while the thermal
requirements are determined by several factors including
ambient temperature, amount of air flow if any, area of the
copper mounting pad, the thermal characteristics of the
MOSFET and its package, and the average current through
the MOSFET.
Typical Performance Curves
FIGURE 2. HGATE (PIN 4) TURNING ON WITH VCC = 12V
FIGURE 3. LGATE (PIN 3) TURNING ON WITH VCC = 12V
FIGURE 4. HGATE (PIN 4) TURNING ON WITH VCC = 5V
FIGURE 5. LGATE (PIN 3)TURNING ON WITH VCC = 5V
NOTES: Device is enabled at 10 milliseconds.
2. Pins 3 and 4 are unconnected.
3. Pins 3 and 4 are connected to the gates of typical high-performance N-Channel MOSFETs.
0
-5
5
10
15
20
25
0
10
30
40
50
20
MILLISECONDS
22nF
NOTE 3
NOTE 2
C1 = 22nF
C1 = 10nF
0
-5
5
10
15
20
25
0
10
30
40
50
20
MILLISECONDS
NOTE 3
NOTE 2
C1 = 22nF
C1 = 10nF
-5
0
5
10
15
0
10
30
40
50
20
MILLISECONDS
NOTE 3
NOTE 2
C1 = 22nF
C1 = 10nF
0
10
20
30
40
50
-5
0
5
10
15
MILLISECONDS
NOTE 3
NOTE 2
C1 = 22nF
C1 = 10nF
HIP1020
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6018BCBZ-T | IC REG TRPL BCK/LINEAR 24-SOIC |
| HIP6021CB-T | IC REG QD BCK/LINEAR 28-SOIC |
| HIP6521CB-T | IC REG QD BCK/LINEAR SYNC 16SOIC |
| HMC920LP5E | IC CTRLR ACTIVE BIAS 32QFN |
| IDTTSE2002B3CNRG | IC TEMP SENS EEPROM DFN-8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP1020CKZ-T | 功能描述:熱插拔功率分布 DEVICE BAY PWR CNTRLR RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HIP1030 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1030_00 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1030AS | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1031 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Half Amp High Side Driver with Overload Protection |
發布緊急采購，3分鐘左右您將得到回復。