- 您現在的位置：買賣IC網 > Datasheet目錄40 > HIP1020CK-T (Intersil)IC CTRLR HOT PLUG SOT23-5 Datasheet資料下載
參數資料
| 型號： | HIP1020CK-T |
| 廠商： | Intersil |
| 文件頁數： | 2/6頁 |
| 文件大小： | 331K |
| 描述： | IC CTRLR HOT PLUG SOT23-5 |
| 標準包裝： | 3,000 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 5V，12V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SC-74A，SOT-753 |
| 供應商設備封裝： | SOT-23-5 |
| 包裝： | 帶卷 (TR) |
2
Pin Descriptions
PIN
SYMBOL
FUNCTION
DESCRIPTION
1
VCC
Bias Supply
Connect this pin to either a 12V or a 5V source. The HIP1020 detects the bias-voltage level at
pin 1 and decides whether to operate as a voltage-doubler or a voltage-tripler. Consequently,
it is not recommended to operate with bias voltages between 5V (?0%) and 12V (?0%). In
the absence of an enable signal at pin 5, the current into pin 1 is less than 1礎. It is necessary
for voltage to be present at pin 1 prior to applying an enable signal at pin 5.
2
GND
Ground
Connect to the negative rail of the supply that is connected to pin 1.
3
LGATE
Gate Driver for the 5V
and/or 3.3V
MOSFET(s)
When VCC = 12V, connect this pin to the gate(s) of the 5V and/or 3.3V MOSFETs. When VCC
= 5V, connect this pin to the gate of a 3.3V MOSFET. Upon a rising edge on EN (pin 5), the
voltage on this pin will ramp linearly to ~16V when VCC = 12V and ~12V when VCC = 5V. An
internal dv/dt activated clamp shunts coupled noise to ground preventing unintended turn on at
either output. The internal dv/dt-activated clamp also protects pin 5.
4
HGATE
12V or 5V MOSFET
Gate Driver
When VCC = 12V, connect this pin to the gate of the 12V MOSFET. When VCC = 5V, connect
this pin to the gate of the 5V MOSFET. Upon a rising edge on EN (pin 5), the voltage on this
pin will ramp linearly to ~22V when VCC = 12V and ~13V when VCC = 5V.
5
EN
Enable
Connect a TTL or 3.3V logic signal to this pin to control the outputs at pins 3 and 4. A rising
edge on pin 5 initiates the linear voltage ramps at pins 3 and 4. Be sure that the device driving
EN does not enter a high-impedance state when enabling is not desired and that its maximum
rise time does not exceed 100祍.
HIP1020
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6018BCBZ-T | IC REG TRPL BCK/LINEAR 24-SOIC |
| HIP6021CB-T | IC REG QD BCK/LINEAR 28-SOIC |
| HIP6521CB-T | IC REG QD BCK/LINEAR SYNC 16SOIC |
| HMC920LP5E | IC CTRLR ACTIVE BIAS 32QFN |
| IDTTSE2002B3CNRG | IC TEMP SENS EEPROM DFN-8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP1020CKZ-T | 功能描述:熱插拔功率分布 DEVICE BAY PWR CNTRLR RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| HIP1030 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1030_00 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1030AS | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1031 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Half Amp High Side Driver with Overload Protection |
發布緊急采購，3分鐘左右您將得到回復。