參數資料
型號： HI7191IP
廠商： HARRIS SEMICONDUCTOR
元件分類： ADC
英文描述： 24-Bit, High Precision, Sigma Delta A/D Converter
中文描述： 1-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDIP20
文件頁數： 10/24頁
文件大?。?/td> 187K
代理商： HI7191IP
1906
Analog Inputs
The analog input on the HI7191 is a fully differential input
with programmable gain capabilities. The input accepts both
unipolar and bipolar input signals and gains range from 1 to
128. The common mode range of this input is from AV
SS
to
AV
DD
provided that the absolute value of the analog input
voltage lies within the power supplies. The input impedance
of the HI7191 is dependent upon the modulator input sam-
pling rate and the sampling rate varies with the selected
PGIA gain. Table 3 below shows the sampling rates and
input impedances for the different gain settings of the
HI7191. Note that this table is valid only for a 10MHz master
clock. If the input clock frequency is changed then the input
impedance will change accordingly. The equation used to
calculate the input impedance is:
where C
in
is the nominal input capacitance (8pF) and f
S
is
the modulator sampling rate.
Bipolar/Unipolar Input Ranges
The input on the HI7191 can accept either unipolar or bipolar
input voltages. Bipolar or unipolar options are chosen by pro-
gramming the B/U bit of the Control Register. Programming
the part for either unipolar or bipolar operation does not
change the input signal conditioning.
The inputs are differential, and as a result are referenced to
the voltage on the V
INLO
input. For example, if V
INLO
is
+1.25V and the HI7191 is configured for unipolar operation
with a gain of 1 and a V
REF
of +2.5V, the input voltage range
on the V
INLO
input is +1.25V to +3.75V. If V
INLO
is +1.25V
and the HI7191 is configured for bipolar mode with gain of 1
and a V
REF
of +2.5V, the analog input range on the V
INHI
input is -1.25V to +3.75V.
Programmable Gain Instrumentation Amplifier
The Programmable Gain Instrumentation Amplifier allows the
user to directly interface low level sensors and bridges directly
to the HI7191. The PGIA has 4 selectable gain options of 1, 2,
4, 8 which are implemented by multiple sampling of the input
signal. Input signals can be gained up further to 16, 32, 64 or
128. These higher gains are implemented in the digital section
of the design to maintain a high signal to noise ratio through
the front end amplifiers. The gain is digitally programmable in
the Control Register via the serial interface. For optimum
PGIA performance the V
CM
pin should be tied to the mid point
of the analog supplies.
Differential Reference Input
The reference inputs of the of the HI7191, V
RHI
and V
RLO
,
provide a differential reference input capability. The nominal
differential voltage (V
REF
= V
RHI
- V
RLO
) is +2.5V and the
common mode voltage cab be anywhere between AV
SS
and
AV
DD
. Larger values of V
REF
can be used without
degradation in performance with the maximum reference
voltage being V
REF
= +5V. Smaller values of V
REF
can also
be used but performance will be degraded since the LSB
size is reduced.
The full scale range of the HI7191 is defined as:
and V
RHI
must always be greater than V
RLO
for proper
operation of the device.
The reference inputs provide a high impedance dynamic
load similar to the analog inputs and the effective input
impedance for the reference inputs can be calculated in the
same manner as it is for the analog input impedance. The
only difference in the calculation is that C
IN
for the reference
inputs is 10.67pF. Therefor, the input impedance range for
the reference inputs is from 149k
in a gain of 8 or higher
mode to 833k
in the gain of 1 mode.
V
CM
Input
The voltage at the V
CM
input is the voltage that the internal
analog circuitry is referenced to and should always be tied to
the midpoint of the AV
DD
and AV
SS
supplies. This point
provides a common mode input voltage for the internal oper-
ational amplifiers and must be driven from a low noise, low
impedance source if it is not tied to analog ground. Failure to
do so will result in degraded HI7191 performance. It is
recommended that V
CM
be tied to analog ground when
operating off of AV
DD
= +5V and AV
SS
= -5V supplies.
V
CM
also determines the headroom at the upper and lower
ends of the power supplies which is limited by the common
mode input range where the internal operational amplifiers
remain in the linear, high gain region of operation. The
HI7191 is designed to have a range of AV
SS
+1.8V < V
CM
<
AV
DD
- 1.8V. Exceeding this range on the V
CM
pin will
compromise the device performance.
Transducer Burn-Out Current Source
The V
INHI
input of the HI7191 contains a 500nA (Typ) current
source which can be turned on/off via the Control Register.
This current source can be used in checking whether a trans-
ducer has burnt-out or become open before attempting to take
measurements on that channel. When the current source is
turned on an additional offset will be created indicating the
presence of a transducer. The current source is controlled by
the BO bit (Bit 4) in the Control Register and is disabled on
power up. See Figure 8 for an applications circuit.
TABLE 3. EFFECTIVE INPUT IMPEDANCE vs GAIN
GAIN
SAMPLING RATE
(kHz)
INPUT IMPEDANCE
(M
)
1
78.125
1.6
2
156.25
0.8
4
312.5
0.4
8, 16, 32, 64, 128
625
0.2
Z
IN
= 1/(C
IN
x f
S
),
FSR
BIPOLAR
= 2 x V
REF
/GAIN
FSR
UNIPOLAR
= V
REF
/GAIN
HI7191
相關PDF資料
PDF描述
HI8182C Telecommunication IC
HI8182CM Telecommunication IC
HI8182R Telecommunication IC
HI8182RM Telecommunication IC
HI8281 Interface IC
相關代理商/技術參數
參數描述
HI7191IPZ 功能描述:模數轉換器 - ADC W/ANNEAL ADC 24BIT SIGMADELTA 20PDIP RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
HI73127 制造商:Hanna 功能描述:Bulk
HI-73127 制造商:HANNA INSTRUMENTS 功能描述:ELECTRODE SPARE 制造商:HANNA INSTRUMENTS 功能描述:ELECTRODE, SPARE 制造商:HANNA INSTRUMENTS 功能描述:ELECTRODE, SPARE; pH Measuring Ranges:-
HI765PWL 制造商:Hanna 功能描述:
HI766C 制造商:Hanna 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*