3-5
Absolute Maximum Ratings TA =25oC
Thermal Information
Supply Voltage, AVCC or DVCC to AGND or DGND . . . . . . . . . . .6V
DGND to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3V
Digital I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DGND to DVCC
Analog I/O Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . AGND to AVCC
Operating Conditions
Temperature Range
HI5662/6IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC
Thermal Resistance (Typical, Note 1)
θ
JA (
oC/W)
HI5662/6IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
(Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specication is not implied.
NOTE:
1.
θJA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specications
AVCC1,2 = DVCC1,2 = +5.0V, DVCC3 = +3.0V; VRIN = 2.50V; fS = 60MSPS at 50% Duty Cycle;
CL = 10pF; TA = 25
oC; Differential Analog Input; Unless Otherwise Specied
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
ACCURACY
Resolution
8
-
Bits
Integral Linearity Error, INL
fIN = 10MHz
-
0.5
-
LSB
Differential Linearity Error, DNL
(Guaranteed No Missing Codes)
fIN = 10MHz
-
±0.2
±1.0
LSB
Offset Error, VOS
fIN = DC
-10
-
+10
LSB
Full Scale Error, FSE
fIN = DC
-
1
-
LSB
DYNAMIC CHARACTERISTICS
Minimum Conversion Rate
No Missing Codes
-
1
-
MSPS
Maximum Conversion Rate
No Missing Codes
60
-
MSPS
Effective Number of Bits, ENOB
fIN = 10MHz
fIN = 10MHz, Single Ended Analog Input
7.5
7.0
7.8
7.7
-
Bits
Signal to Noise and Distortion Ratio, SINAD
fIN = 10MHz
-
48.7
-
dB
Signal to Noise Ratio, SNR
fIN = 10MHz
-
48
-
dB
Total Harmonic Distortion, THD
fIN = 10MHz
-
-66
-
dBc
2nd Harmonic Distortion
fIN = 10MHz
-
-71
-
dBc
3rd Harmonic Distortion
fIN = 10MHz
-
-71
-
dBc
Spurious Free Dynamic Range, SFDR
fIN = 10MHz
-
71
-
dBc
Intermodulation Distortion, IMD
f1 = 1MHz, f2 = 1.02MHz
-
64
-
dBc
I/Q Channel Crosstalk
-
-75
-60
dBc
I/Q Channel Offset Match
-
2.5
-
LSB
I/Q Channel Full Scale Error Match
-
2.5
-
LSB
Transient Response
(Note 2)
-
1
-
Cycle
Over-Voltage Recovery
0.2V Overdrive (Note 2)
-
1
-
Cycle
RMS Signal
RMS Noise + Distortion
--------------------------------------------------------------
=
RMS Signal
RMS Noise
-------------------------------
=
HI5662