- 您現在的位置：買賣IC網 > PDF目錄371814 > HI5628IN (HARRIS SEMICONDUCTOR) Power Resistor; Series:200; Resistance:1ohm; Resistance Tolerance:+/- 5%; Power Rating:8W; Resistor Element Material:Ceramic; Temperature Coefficient:+/-400 ppm; Leaded Process Compatible:Yes; Packaging:Bulk RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | HI5628IN |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | DAC |
| 英文描述： | Power Resistor; Series:200; Resistance:1ohm; Resistance Tolerance:+/- 5%; Power Rating:8W; Resistor Element Material:Ceramic; Temperature Coefficient:+/-400 ppm; Leaded Process Compatible:Yes; Packaging:Bulk RoHS Compliant: Yes |
| 中文描述： | DUAL, PARALLEL, 8 BITS INPUT LOADING, 0.015 us SETTLING TIME, 8-BIT DAC, PQFP48 |
| 文件頁數： | 8/10頁 |
| 文件大小： | 93K |
| 代理商： | HI5628IN |
8
parallel resistance of the output 50
and the oscilloscope’s
50
input. This also aids the ability to resolve the specified
error band without overdriving the oscilloscope.
Singlet Glitch Area,
is the switching transient appearing on
the output during a code transition. It is measured as the
area under the overshoot portion of the curve and is
expressed as a Volt-Time specification.
Full Scale Gain Error
, is the error from an ideal ratio of 32
between the output current and the full scale adjust current
(through R
SET
).
Full Scale Gain Drift,
is measured by setting the data inputs
to all ones and measuring the output voltage through a
known resistance as the temperature is varied from T
MIN
to
T
MAX
. It is defined as the maximum
deviation
from the
value
measured at room temperature to the
value
measured at
either T
MIN
or T
MAX
. The units are ppm of FSR (Full Scale
Range) per degree C.
TotalHarmonicDistortion,THD
,istheratio ofthe DACoutput
fundamental to the RMS sum of the first five harmonics.
Spurious Free Dynamic Range, SFDR
, is the amplitude
difference from the fundamental to the largest harmonically
or non-harmonically related spur within the specified
window.
Output Voltage Compliance Range,
is the voltage limit
imposed on the output. The output impedance load should
be chosen such that the voltage developed does not violate
the compliance range.
Offset Error,
is measured by setting the data inputs to all
zeros and measuring the output voltage through a known
resistance. Offset error is defined as the maximum
deviation
of the output current from a value of 0mA.
Offset Drift,
is measured by setting the data inputs to all
zeros and measuring the output voltage through a known
resistance as the temperature is varied from T
MIN
to T
MAX
.
It is defined as the maximum
deviation
from the
value
measured at room temperature to the
value
measured at
either T
MIN
or T
MAX
. The units are ppm of FSR (Full Scale
Range) per degree C.
Power Supply Rejection,
is measured using a single power
supply. Its nominal +5V is varied
±
10% and the change in the
DAC full scale output is noted.
Reference Input Multiplying Bandwidth,
is defined as the
3dB bandwidth of the voltage reference input. It is measured
by using a sinusoidal waveform as the external reference
with the digital inputs set to all 1s. The frequency is
increased until the amplitude of the output waveform is 0.707
of its original value.
Internal Reference Voltage Drift,
is defined as the
maximum
deviation
from the
value
measured at room
temperature to the
value
measured at either T
MIN
or T
MAX
.
The units are ppm per degree C.
Detailed Description
The HI5628 is a dual, 8-bit, current out, CMOS, digital to
analog converter. Its maximum update rate is 165MSPS and
can be powered by either single or dual power supplies in
the recommended range of +3V to +5V. It consumes less
than 330mW of power when using a +5V supply with the
data switching at 100MSPS. The architecture is based on a
segmented current source arrangement that reduces glitch
by reducing the amount of current switching at any one time.
The five MSBs are represented by 31 major current sources
of equivalent current. The three LSBs are comprised of
binary weighted current sources. Consider an input pattern
to the converter which ramps through all the codes from 0 to
255. The three LSB current sources would begin to count up.
When they reached the all high state (decimal value of 7)
and needed to count to the next code, they would all turn off
and the first major current source would turn on. To continue
counting upward, the 3 LSBs would count up another 7
codes, and then the next major current source would turn on
and the three LSBs would all turn off. The process of the
single, equivalent, major current source turning on and the
three LSBs turning off each time the converter reaches
another 7 codes greatly reduces the glitch at any one
switching point. In previous architectures that contained all
binary weighted current sources or a binary weighted
resistor ladder, the converter might have a substantially
larger amount of current turning on and off at certain, worst-
case transition points such as midscale and quarter scale
transitions. By greatly reducing the amount of current
switching at certain ‘major’ transitions, the overall glitch of
the converter is dramatically reduced, improving settling
times and transient problems.
Digital Inputs and Termination
The HI5628 digital inputs are guaranteed to CMOS levels.
However, TTL compatibility can be achieved by lowering the
supply voltage to 3V due to the digital threshold of the input
buffer being approximately half of the supply voltage. The
internal register is updated on the rising edge of the clock. To
minimize reflections, proper termination should be
implemented. If the lines driving the clock and the digital
inputs are 50
lines, then 50
termination resistors should be
placed as close to the converter inputs as possible, connected
to the digital ground plane (if separate grounds are used).
Ground Plane(s)
If separate digital and analog ground planes are used, then all
of the digital functions of the device and their corresponding
components should be over the digital ground plane and
terminated to the digital ground plane. The same is true for
the analog components and the analog ground plane. The
converter will function properly with a single ground plane, as
the Evaluation Board is configured in this matter.
HI5628
相關PDF資料 |
PDF描述 |
|---|---|
| HI5630 | Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
| HI5630CN | Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
| HI5630EVAL | Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
| HI5634 | High Performance Programmable Phase-Locked Loop for LCD Applications |
| HI5634CB | High Performance Programmable Phase-Locked Loop for LCD Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI5628INZ | 功能描述:數模轉換器- DAC D/A DL 8-BIT 125MSPS 48 LQFP IND TEMP RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| HI5630 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
| HI5630/8CN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI5630/8CN WAF | 制造商:Harris Corporation 功能描述: |
| HI5630_03 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
發布緊急采購，3分鐘左右您將得到回復。