參數資料
型號： HFBR-5103
英文描述： 1300 nm 2000 m，FDDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300 nm 2000 m，FDDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
中文描述： 1300納米2000米，光纖分布式數據介面，100 Mbps的自動取款機，并在低成本1x9封裝形式快速以太網收發器（1300納米2000米，光纖分布式數據介面，100 Mbps的自動取款機，快速以太網收發器（低價格1x9封裝類型））
文件頁數： 21/24頁
文件大?。?/td> 351K
代理商： HFBR-5103
21
11. These optical power values are
measured with the following
conditions:
The Beginning of Life (BOL) to
the End of Life (EOL) optical
power degradation is typically 1.5
dB per the industry convention for
long wavelength LEDs. The actual
degradation observed in Agilent’s
1300 nm LED products is < 1 dB,
as specified in this data sheet.
Over the specified operating voltage
and temperature ranges.
With HALT Line State, (12.5 MHz
square-wave), input signal.
At the end of one meter of noted
optical fiber with cladding modes
removed.
The average power value can be
converted to a peak power value by
adding 3 dB. Higher output optical
power transmitters are available on
special request.
12. The same comments of note 11
apply except that industry conven-
tion for short wavelength LED (800
nm) BOL to EOL aging is 3 dB. This
value for Output Optical Power will
provide a minimum of a 6 dB optical
power budget at the EOL, which
will provide at least 500 meter link
lengths with margin left over for
overcoming normal passive losses,
such as in line connectors, in the
cable plant. The actual degradation
observed in normal commercial
environments will be considerably
less than this amount with Hewlett-
Packard’s 800 nm LED products.
Please consult with your local HP
sales representative for further
details.
13. The Extinction Ratio is a measure of
the modulation depth of the optical
signal. The data “0” output optical
power is compared to the data “1”
peak output optical power and
expressed as a percentage. With the
transmitter driven by a HALT Line
State (12.5 MHz square-wave)
signal, the average optical power is
measured. The data “1” peak power
is then calculated by adding 3 dB to
the measured average optical power.
The data “0” output optical power is
found by measuring the optical
power when the transmitter is
driven by a logic “0” input. The
extinction ratio is the ratio of the
optical power at the “0” level
compared to the optical power at the
“1” level expressed as a percentage
or in decibels.
14. The transmitter provides compliance
with the need for Transmit_Disable
commands from the FDDI SMT layer
by providing an Output Optical Power
level of < -45 dBm average in
response to a logic “0” input. This
specification applies to either 62.5/
125
μ
m or 50/125
μ
m fiber cables.
15. This parameter complies with the
FDDI PMD requirements for the
tradeoffs between center wave-
length, spectral width, and rise/fall
times shown in Figure 9.
16. This parameter complies with the
optical pulse envelope from the
FDDI PMD shown in Figure 10. The
optical rise and fall times are
measured from 10% to 90% when
the transmitter is driven by the
FDDI HALT Line State (12.5 MHz
square-wave) input signal.
16a. The optical rise and fall times are
measured from 10% to 90% when
the transmitter is driven by the
FDDI HALT Line State (12.5 MHz
square-wave) input signal.
17. Duty Cycle Distortion contributed
by the transmitter is measured at a
50% threshold using an IDLE Line
State, 125 MBd (62.5 MHz square-
wave), input signal. See Application
Information - Transceiver Jitter
Performance Section of this data
sheet for further details.
18. Data Dependent Jitter contributed
by the transmitter is specified with
the FDDI test pattern described in
FDDI PMD Annex A.5. See Applica-
tion Information - Transceiver Jitter
Performance Section of this data
sheet for further details.
19. Random Jitter contributed by the
transmitter is specified with an
IDLE Line State, 125 MBd (62.5
MHz square-wave), input signal.
See Application Information -
Transceiver Jitter Performance
Section of this data sheet for further
details.
20. This specification is intended to
indicate the performance of the
receiver section of the transceiver
when Input Optical Power signal
characteristics are present per the
following definitions. The Input
Optical Power dynamic range from
the minimum level (with a window
time-width) to the maximum level is
the range over which the receiver is
guaranteed to provide output data
with a Bit Error Ratio (BER) better
than or equal to 2.5 x 10
-10
.
At the Beginning of Life (BOL)
Over the specified operating
temperature and voltage ranges
Input symbol pattern is the FDDI
test pattern defined in FDDI PMD
Annex A.5 with 4B/5B NRZI
encoded data that contains a duty
cycle base-line wander effect of
50 kHz. This sequence causes a
near worst case condition for
inter-symbol interference.
Receiver data window time-width
is 2.13 ns or greater and centered
at mid-symbol. This worst case
window time-width is the
minimum allowed eye-opening
presented to the FDDI PHY
PM._Data indication input (PHY
input) per the example in FDDI
PMD Annex E. This minimum
window time-width of 2.13 ns is
based upon the worst case FDDI
PMD Active Input Interface
optical conditions for peak-to-peak
DCD (1.0 ns), DDJ (1.2 ns) and RJ
(0.76 ns) presented to the
receiver.
To test a receiver with the worst
case FDDI PMD Active Input jitter
condition requires exacting control
over DCD, DDJ and RJ jitter compo-
nents that is difficult to implement
with production test equipment. The
receiver can be equivalently tested
to the worst case FDDI PMD input
jitter conditions and meet the
minimum output data window time-
width of 2.13 ns. This is accom-
plished by using a nearly ideal input
optical signal (no DCD, insignificant
DDJ and RJ) and measuring for a
wider window time-width of 4.6 ns.
This is possible due to the cumula-
tive effect of jitter components
through their superposition (DCD
and DDJ are directly additive and
RJ components are rms additive).
Specifically, when a nearly ideal
input optical test signal is used and
the maximum receiver peak-to-peak
jitter contributions of DCD (0.4 ns),
DDJ (1.0 ns), and RJ (2.14 ns) exist,
the minimum window time-width
becomes 8.0 ns -0.4 ns - 1.0 ns - 2.14
ns = 4.46 ns, or conservatively
4.6 ns. This wider window time-
width of 4.6 ns guarantees the FDDI
PMD Annex E minimum window
time-width of 2.13 ns under worst
case input jitter conditions to the
Hewlett-Packard receiver.
Transmitter operating with an
IDLE Line State pattern, 125
MBd (62.5 MHz square-wave),
相關PDF資料
PDF描述
HFBR-5103T 1300 nm 2000 m，FDDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300 nm 2000 m，FDDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
HFBR-5104T 800 nm 500 m，FDDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(800 nm 500 m，FDDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
HFBR-5105T 1300nm 500 m，FDDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300nm 500 m，FDDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
HFBR-5104 800 nm 500 m，FDDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(800 nm 500 m，FDDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
HFBR-5107T 820 nm，100VG-AnyLAN Multimode Fiber Transceivers in Low Cost 1x9 Package Style(820 nm，100VG-AnyLAN 多模式光收發器（低價格 1x9封裝類型）)
相關代理商/技術參數
參數描述
HFBR-5103A 制造商:Rochester Electronics LLC 功能描述: 制造商:Avago Technologies 功能描述:
HFBR-5103AT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:125 MBd ATM and Fast Ethernet Transceiver in Low Cost 1x9 Package: Extended Temp.. ST Receptacle
HFBR-5103E 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm
HFBR-5103F 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm
HFBR-5103J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*