- 您現在的位置：買賣IC網 > PDF目錄371807 > HFA3842IN96 (INTERSIL CORP) Wireless LAN Medium Access Controller PDF資料下載
參數資料
| 型號： | HFA3842IN96 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Wireless LAN Medium Access Controller |
| 中文描述： | 1 CHANNEL(S), 11M bps, LOCAL AREA NETWORK CONTROLLER, PQFP128 |
| 封裝： | 14 X 20 MM, PLASTIC, MS-026BHB, LQFP-128 |
| 文件頁數： | 23/26頁 |
| 文件大小： | 512K |
| 代理商： | HFA3842IN96 |
23
Power Sequencing
The HFA3842 provides a number of firmware controlled port
pins that are used for controlling the power sequencing and
other functions in the front end components of the PHY.
Packet transmission requires precise control of the radio.
Ideally, energy at the antenna ceases after the last symbol of
information has been transmitted. Additionally, the
transmit/receive switch must be controlled properly to protect
the receiver. It's also important to apply appropriate
modulation to the PA while it's active.
Signaling sequences for the beginning and end of normal
transmissions are illustrated in Figure 25. Table 10 lists
applicable delays.
A transmission begins with PE2 as shown in Figure 25. Next,
the transmit/receive switch is configured for transmission via
the differential pair TR_SW and TR_SW_BAR. This is
followed by TX_PE which activates the transmit state
machine in the BBP. Lastly, PA_PE activates the PA. Delays
for these signals related to the initiation of transmission are
referenced to PE2.
Immediately after the final data bit has been clocked out of
the HFA3842, TX_PE is de-asserted. The HFA3842 then
waits for TXRDY to go inactive, signaling that the BBP has
modulated the final information-rich symbol. It then
immediately de-asserts PA_PE followed by placing the
transmit/receive switch in the receive position and ending
with PE2 going high. Delays for these signals related to the
termination of transmission are referenced to the rising edge
of PE2.
PE1 and PE2 encoding details are found in Table 11.
Note that during normal receive and transmit operation that
PE1 is static and PE2 toggles for receive and transmit
.
TABLE 10. TRANSMIT CONTROL TIMING SPECIFICATIONS
PARAMETER
SYMBOL
DELAY
TOLERANCE
UNITS
PE2 to TR Switch
t
D1
2
±
0.1
μ
s
PE2 to PA_PE
t
D3
3
±
0.1
μ
s
PA_PE to PE2
t
D4
3
±
0.1
μ
s
TR Switch to PE2
t
D5
2
±
0.1
μ
s
FIGURE 25. TRANSMIT CONTROL SIGNAL SEQUENCING
PE1
PE2
TR_SW
TR_SW_BAR
TX_PE
TX_RDY
PA_PE
t
D1
t
D5
t
D3
t
D4
TABLE 11. POWER ENABLE STATES
PE1
PE2
PLL_PE
Power Down State
0
0
1
Receive State
1
1
1
Transmit State
1
0
1
PLL Active State
0
1
1
PLL Disable State
X
X
0
NOTE:
22. PLL_PE is controlled via the serial interface, and can be used to
disable the internal synthesizer, the actual synthesizer control is
an AND function of PLL_PE, and a result of the OR function of
PE1 and PE2. PE1 and PE2 will directly control the power
enable functionality of the LO buffer(s)/phase shifter.
TABLE 11. POWER ENABLE STATES
PE1
PE2
PLL_PE
HFA3842
相關PDF資料 |
PDF描述 |
|---|---|
| HFA3842 | Wireless LAN Medium Access Controller |
| HFA3842IN | Wireless LAN Medium Access Controller |
| HFA3860AIV96 | Circular Connector; No. of Contacts:5; Series:MS27473; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:10; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:10-5 RoHS Compliant: No |
| HFA3860A | Direct Sequence Spread Spectrum Baseband |
| HFA3860AIV | 3.3V 288-mc CPLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFA3860 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:11 Mbps Direct Sequence Spread Spectrum Baseband Processor |
| HFA3860A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Direct Sequence Spread Spectrum Baseband |
| HFA3860AEVAL1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述: |
| HFA3860AIV | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Direct Sequence Spread Spectrum Baseband |
| HFA3860AIV WAF | 制造商:Harris Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。