
647
Table 24.2 DC Characteristics (2) (cont)
– Preliminary –
Conditions:V
CC = 4.0 V to 5.5 V*
7, AV
CC*
1 = 4.0 V to 5.5 V, V
SS = AVSS*
1 = 0 V,
T
a = –20 to +75°C*
7 (regular specifications), T
a = –40 to +85°C*
7 (wide-range
specifications)
Item
Symbol
Min
Typ
Max
Unit
Test Conditions
Input
capacitance
5(6
(4)
C
in
——
80
pF
V
in = 0 V,
f = 1 MHz,
NMI
—
50
pF
T
a = 25°C
P52, P97,
P42, P86
——
20
pF
Input pins except
(4) above
——
15
pF
Current
dissipation*
8
Normal operation
I
CC
—
65
85
mA
f = 16 MHz,
H8S/2134 Series
—
70
100
mA
f = 16 MHz,
H8S/2138 Series
Sleep mode
—
50
70
mA
f = 16 MHz,
H8S/2134 Series
—
60
85
mA
f = 16 MHz,
H8S/2138 Series
Standby mode*
9
—
0.01
5.0
A
T
a ≤ 50°C
—
20.0
A
50°C < T
a
Analog power
During A/D, D/A
conversion
Al
CC
—
3.2
7.0
mA
supply current
Idle
—
0.01
5.0
A
AV
CC =
2.0 V to 5.5 V
Analog power supply voltage*
1
AV
CC
4.0
—
5.5
V
Operating
2.0
—
5.5
V
Idle/not used
RAM standby voltage
V
RAM
2.0
—
V
Notes:
1.
Do not leave the AVCC, and AVSS pins open even if the A/D converter and D/A converter are not
used.
Even if the A/D converter and D/A converter are not used, apply a value in the range
2.0 V to 5.5 V to AVCC by connection to the power supply (V
CC), or some other method.
2.
P67 to P60 include supporting module inputs multiplexed on those pins.
3.
,54 includes the $'75* signal multiplexed on that pin.
4.
In the H8S/2138 Series, P52/SCK0/SCL0 and P97/SDA0 are NMOS push-pull outputs.
An external pull-up resistor is necessary to provide high-level output from SCL0 and SDA0 (ICE = 1).
P52/SCK0 and P97 (ICE = 0) high levels are driven by NMOS.
5.
In the H8S/2138 Series, When ICE = 0. Low-level output when the bus drive function is selected is
determined separately.
6.
The upper limit of the port 6 applied voltage is V
CC + 0.3 V when CIN input is not selected, and the
lower of V
CC + 0.3 V and AVCC + 0.3 V when CIN input is selected. When a pin is in output mode, the
output voltage is equivalent to the applied voltage.
7.
Ranges of V
CC = 4.5 to 5.5 V, Ta = 0 to +75°C (regular specifications), and Ta = 0 to +85°C (wide-
range specifications) must be observed for flash memory programming/erasing.
8.
Current dissipation values are for V
IH min = VCC – 0.5 V and VIL max = 0.5 V with all output pins
unloaded and the on-chip pull-up MOSs in the off state.
9.
The values are for V
RAM ≤ VCC < 4.5 V, VIH min = VCC × 0.9, and VIL max = 0.3 V.