- 您現在的位置：買賣IC網 > PDF目錄370464 > HD61830A00H (Hitachi,Ltd.) LCDC (LCD Timing Controller) PDF資料下載
參數資料
| 型號： | HD61830A00H |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | LCDC (LCD Timing Controller) |
| 中文描述： | LCDC（LCD定時控制器） |
| 文件頁數： | 7/43頁 |
| 文件大小： | 173K |
| 代理商： | HD61830A00H |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
HD61830/HD61830B
7
Block Functions
Registers
The HD61830/HD61830B has the five types of registers: instruction register (IR), data input register (DIR),
data output register (DOR), dot registers (DR), and mode control register (MCR).
The IR is a 4-bit register that stores the instruction codes for specifying MCR, DR, a start address register,
a cursor address register, and so on. The lower order 4 bits DB0
to DB3 of data buses are written in it.
The DIR is an 8-bit register used to temporarily store the data written into the external RAM, DR, MCR,
and so on.
The DOR is an 8-bit register used to temporarily store the data read from the external RAM. Cursor address
information is written into the cursor address counter (CAC) through the DIR. When the memory read
instruction is set in the IR (latched at the falling edge of E signal), the data of external RAM is read to DOR
by an internal operation. The data is transferred to the MPU by reading the DOR with the next instruction
(the contents of DOR are output to the data bus when E is at the high level).
The DR are registers used to store dot information such as character pitches and the number of vertical
dots, and so on. The information sent from the MPU is written into the DR via the DIR.
The MCR is a 6-bit register used to store the data which specifies states of display such as display on/off
and cursor on/off/blink. The information sent from the MPU is written in it via the DIR.
Busy Flag (BF)
The busy flag = 1 indicates the HD61830 is performing an internal operation. Instructions cannot be
accepted. As shown in Control Instruction, read busy flag, the busy flag is output on DB7 under the
conditions of RS = 1, R/W = 1, and E = 1. Make sure the busy flag is 0 before writing the next instruction.
Dot Counters (DC)
The dot counters are counters that generate liquid crystal display timing according to the contents of DR.
相關PDF資料 |
PDF描述 |
|---|---|
| HD61830 | LCDC (LCD Timing Controller) |
| HD61830B | LCDC (LCD Timing Controller) |
| HD61830B00H | LCDC (LCD Timing Controller) |
| HD6301X0 | CMOS MCU |
| HD6301X0CP | CMOS MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD61830B | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:LCDC (LCD Timing Controller) |
| HD61830B00 | 制造商:HITCHI 功能描述: |
| HD61830B00H | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:LCDC (LCD Timing Controller) |
| HD61945MP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Phase-Locked Loop |
| HD6301V0P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。