- 您現在的位置：買賣IC網 > PDF目錄370461 > HD404849TF (Hitachi,Ltd.) TERMINAL PDF資料下載
參數資料
| 型號： | HD404849TF |
| 廠商： | Hitachi,Ltd. |
| 元件分類： | 其它接口 |
| 英文描述： | TERMINAL |
| 中文描述： | IGBT模塊 |
| 文件頁數： | 60/125頁 |
| 文件大?。?/td> | 471K |
| 代理商： | HD404849TF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
HD404849 Series
60
Timer B Operations:
Free-running/reload timer operation: The free-running/reload operation, input clock source, and
prescaler division ratio are selected by timer mode register B1 (TMB1: $009).
Timer B is initialized to the value set in timer write register B (TWBL: $00A, TWBU: $00B) by
software and incremented by one at each clock input. If an input clock is applied to timer B after it has
reached $FF, an overflow is generated. In this case, if the reload timer function is enabled, timer B is
initialized to its initial value set in timer write register B; if the free-running timer function is enabled,
the timer is initialized to $00 and then incremented again.
The overflow sets the timer B interrupt request flag (IFTB: $002, bit 0). IFTB is reset by software or
MCU reset. Refer to figure 3 and table 1 for details.
External event counter operation: Timer B is used as an external event counter by selecting external
event input as the input clock source. In this case, pin R1
3
/
EVNB
must be set to
EVNB
by port mode
register C (PMRC: $025).
Timer B is incremented by one at each falling edge of signals input to pin
EVNB
. The other operations
are basically the same as the free-running/reload timer operation.
Timer output operation: The following three output modes can be selected for timer B by setting timer
mode register B2 (TMB2: $013).
Toggle
0 output
1 output
By selecting the timer output mode, pin R1
0
/TOB is set to TOB. The output from TOB is reset low by
MCU reset.
Toggle output: When toggle output mode is selected, the output level is inverted if a clock is input
after timer B has reached $FF. By using this function and reload timer function, clock signals can
be output at a required frequency for the buzzer. The output waveform is shown in figure 43 (1).
0 output: When 0 output mode is selected, the output level is pulled low if a clock is input after
timer B has reached $FF. Note that this function must be used only when the output level is high.
1 output: When 1 output mode is selected, the output level is set high if a clock is input after timer
B has reached $FF. Note that this function must be used only when the output level is low.
相關PDF資料 |
PDF描述 |
|---|---|
| HD4074849 | TERMINAL |
| HD4074849FS | CONTACT |
| HD4074849H | CONTACT |
| HD4074849TF | TERMINAL |
| HD404864 | Low-Voltage AS Microcomputers with On-Chip LCD Circuit(片上LCD電路的低壓微計算機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD404868 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip LCD Circuit |
| HD404878 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip LCD Circuit |
| HD4048812 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip LCD Circuit |
| HD4048812H | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip LCD Circuit |
| HD4048812TE | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip LCD Circuit |
發布緊急采購，3分鐘左右您將得到回復。