- 您現在的位置：買賣IC網 > PDF目錄370450 > HCPL-070A Very Low Power Consumption High Gain Optocouplers(極低功率消耗的高增益光耦合器) PDF資料下載
參數資料
| 型號： | HCPL-070A |
| 英文描述： | Very Low Power Consumption High Gain Optocouplers(極低功率消耗的高增益光耦合器) |
| 中文描述： | 非常低的功耗高增益光電耦合器（極低功率消耗的高增益光耦合器） |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 298K |
| 代理商： | HCPL-070A |
13
Propagation Delay
When the HCPL-47XX optocoup-
ler is operated under very low
input and output current condi-
tions, the propagation delay times
will lengthen. When lower input
drive current level is used to
switch the high-efficiency AlGaAs
LED, the slower the charge and
discharge time will be for the
LED. Correspondingly, the propa-
gation delay times will become
longer as a result. In addition, the
split-Darlington (open-collector)
output amplifier needs a larger,
pull-up load resistance to ensure
the output current is within a
controllable range. Applications
that are not sensitive to longer
propagation delay times and that
are easily served by this HCPL-
47XX optocoupler, typically 65
μ
s
or greater, are those of status
monitoring of a telephone line,
power line, battery condition of a
portable unit, etc. For faster
HCPL-47XX propagation delay
times, approximately 30
μ
s, this
optocoupler needs to operate at
higher I
F
(
≥
500
μ
A) and I
o
(
≥
1 mA) levels.
Applications
Battery-Operated Equipment
Common applications for the
HCPL-47XX optocoupler are
within battery-operated, portable
equipment, such as test or
medical instruments, computer
peripherals and accessories where
energy conservation is required to
maximize battery life. In these
applications, the optocoupler
would monitor the battery voltage
and provide an isolated output to
another electrical system to
indicate battery status or the need
to switch to a backup supply or
begin a safe shutdown of the
equipment via a communication
port. In addition, the HCPL-47XX
optocouplers are specified to
operate with 3 Vdc CMOS logic
family of devices to provide logic-
signal isolation between similar or
different logic circuit families.
Telephone Line Interfaces
Applications where the HCPL-
47XX optocoupler would be best
used are in telephone line inter-
face circuitry for functions of ring
detection, on-off hook detection,
line polarity, line presence and
supplied-power sensing. In
particular, Integrated Services
Digital Network (ISDN) applica-
tions, as illustrated in Figure 10,
can severely restrict the input
power that an optocoupler inter-
face circuit can use (approxi-
mately 3 mW). Figure 10 shows
three isolated signals that can be
served by the small input LED
current of the HCPL-47XX dual-
and single-channel optocouplers.
Very low, total power dissipation
occurs with these series of
devices.
Switched-Mode Power
Supplies
Within Switched-Mode Power
Supplies (SMPS) the less power
consumed the better. Isolation for
monitoring line power, regulation
status, for use within a feedback
path between primary and
secondary circuits or to external
circuits are common applications
for optocouplers. Low-power
HCPL-47XX optocoupler can help
keep higher energy conversion
efficiency for the SMPS. The block
diagram of Figure 11 shows where
low-power isolation can be used.
Table 1. Typical HCPL-4701 Power Dissipation for 3 V and 5 V Applications
V
CC
= 3.3 Vdc
(
μ
W)
I
F
= 40
μ
A
P
LED
50
P
Vcc
65
P
O-C[1]
20
P
TOTAL[2]
135
μ
W
V
CC
= 5 Vdc
I
F
= 500
μ
A
625
330
10
965
μ
W
I
F
= 40
μ
A
50
100
25
175
μ
W
I
F
= 500
μ
A
625
500
20
1,145
μ
W
Notes:
1. R
L
of 11 k
open-collector (o-c) pull-up resistor was used for both 3.3 Vdc and 5 Vdc calculations.
2. For typical total interface circuit power consumption in 3.3 Vdc application, add to P
TOTAL
approximately 80
μ
W for 40
μ
A
(1,025
μ
W for 500
μ
A) LED current-limiting resistor, and 960
μ
W for the 11 k
pull-up resistor power dissipations. Similarly, for 5
Vdc applications, add to P
TOTAL
approximately 150
μ
W for 40
μ
A (1,875
μ
W for 500
μ
A) LED current-limiting resistor and 2,230
μ
W for the 11 k
pull-up resistor power dissipations.
Power Dissipation
相關PDF資料 |
PDF描述 |
|---|---|
| HCPL-2530 | Dual Channel, High Speed Optocouplers(雙通道，高速光耦合器) |
| HCPL-2531 | Dual Channel, High Speed Optocouplers(雙通道，高速光耦合器) |
| HCPL-2602 | High CMR Line Receiver Optocouplers(高共態抑制線接收光耦器) |
| HCPL-261A | HCMOS Compatible, High CMR, 10 MBd Optocouplers |
| HCPL-261N | High CMR, High Speed TTL Compatible Optocouplers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCPL070A#060 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DARLINGTON-NPN-OUTPUT DC-INPUT OPTOCOUPLER |
| HCPL-070A#060 | 功能描述:高速光耦合器 100kBd 1Ch 10mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| HCPL-070A#500 | 功能描述:高速光耦合器 100kBd 1Ch 10mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| HCPL-070A#560 | 功能描述:高速光耦合器 100kBd 1Ch 10mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
| HCPL-070A-000E | 功能描述:高速光耦合器 100kBd 1Ch 10mA RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。