- 您現在的位置：買賣IC網 > PDF目錄370429 > HB28E016MM2 (Hitachi,Ltd.) MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte PDF資料下載
參數資料
| 型號： | HB28E016MM2 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte |
| 中文描述： | 多媒體16 Mbyte/32 Mbyte/64 Mbyte/128字節 |
| 文件頁數： | 4/88頁 |
| 文件大小： | 329K |
| 代理商： | HB28E016MM2 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
HB28E016/D032/D064/B128MM2
4
Interface
These Hitachi MultiMediaCards' interface can operate in two different modes:
MultiMediaCard mode
SPI mode
Both modes are using the same pins. The default mode is the MultiMediaCard mode. The SPI mode is
selected by activating (= 0) the CS signal (Pin1) and sending the CMD0.
MultiMediaCard Mode
n the MultiMediaCard mode, all data is transferred over a minimal number of lines:
CLK: with each cycle of this signal a one-bit transfer on the command and data lines is done. The
frequency may vary between zero and the maximum clock frequency. The MultiMediaCard bus master
is free to generate these cycles without restrictions in the range of 0 to 20 MHz.
CMD: is a bidirectional command channel used for card initialization and data transfer commands.
The CMD signal has two operation modes: open drain for initialization mode and push pull for fast
command transfer. Commands are sent from the MultiMediaCard bus master to the MultiMediaCard
and responses vice versa.
DAT: is a bidirectional data channel with a width of one line. The DAT signal of the MultiMediaCard
operates in push pull mode.
RSV: is pulled up with resistor (2 M
typ) in the MultiMediaCard. The external pull-up resistor should
be recommended if the system requires.
I
MultiMediaCard Host
ROD
RDAT
RCMD
1 2 3 4 5 6 7
MultiMediaCard
CMD
DAT
CLK
MultiMediaCard Mode Interface
All MultiMediaCards are connected directly to the lines of the MultiMediaCard bus. The following table
defines the card contacts.
相關PDF資料 |
PDF描述 |
|---|---|
| HB28C048A6 | FLASH ATA Card |
| HB28C048C6 | CompactFlash⑩ |
| HB28C016A6 | FLASH ATA Card |
| HB28C016C6 | CompactFlash⑩ |
| HB28C032A6 | FLASH ATA Card |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HB2A102K-S265B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
| HB2A102K-S565B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
| HB2A103K-S565B | 制造商:Hitano Enterprise Corp 功能描述: |
| HB2A122K-S265B | 制造商:Hitano Enterprise Corp 功能描述: |
| HB2A122K-S565B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
發布緊急采購，3分鐘左右您將得到回復。