參數資料
型號： HB28E016MM2
廠商： Hitachi,Ltd.
英文描述： MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte
中文描述： 多媒體16 Mbyte/32 Mbyte/64 Mbyte/128字節
文件頁數： 34/88頁
文件大?。?/td> 329K
代理商： HB28E016MM2
HB28E016/D032/D064/B128MM2
34
Data Transfer Mode
When in Standby State, both CMD and DAT lines are in the push-pull mode. As long as the content of all
CSD registers is not known, the f
PP
clock rate is equal to the slow f
OD
clock rate. SEND_CSD (CMD9)
allows the host to get the Card Specific Data (CSD register), e.g. ECC type, block length, card storage
capacity, maximum clock rate etc..
CMD9, 10
CMD24, 25
CMD12 or
''transfer end''
CMD28, 29, 38
CMD16, 23, 32...37
CMD13
no state transition
in data-transfer mode
CMD7
Stand-by state
(stby)
Disconnect state
(dis)
Programming state
(prg)
Receive-data state
(rcv)
Sending-data state
(data)
Transfer state
(tran)
from all states in
data-transfer mode
data-transfer mode
card-identification mode
CMD15
CMD0
CMD3
''operation
complete''
''operation
complete''
CMD7
CMD12,
''operation
complete''
CMD11, 17, 18, 30
CMD7
CMD7
CMD20, 24, 25, 26, 27, 42
MultiMediaCard State Diagram
(Data Transfer Mode)
The command SELECT_DESELECT_CARD (CMD7) is used to select one card and place it in the
Transfer State. If a previously selected card is in the Transfer State its connection with the host is released
and it will move back to the Stand-by State. Only one card can be, at any time, in the Transfer State. A
selected card is responding the CMD7, the deselected one does not respond to this command. When
CMD7 is sent including the reserved relative card address 0x0000, all cards transfer back to Stand-by State.
This command is used to identify new cards without resetting other already acquired cards. Cards to which
an RCA has already been assigned, do not respond to the identification command flow in this state. All the
data communication in the Data Transfer Mode is consequently a point-to point communication between
the host and the selected card (using addressed commands). All addressed commands are acknowledged by
a response on the CMD line. All read commands (data is sent from the card via data lines) can be
interrupted at any time, by a stop command. The data transfer will terminate and the card will stop or start
working on the next command. The DAT bus line signal level is high when no data is transmitted. A
transmitted data block consists of a start bit (LOW), followed by a continuous data stream. The data stream
contains the net payload data (and error correction bits if an off-card ECC is used). The data stream ends
相關PDF資料
PDF描述
HB28C048A6 FLASH ATA Card
HB28C048C6 CompactFlash⑩
HB28C016A6 FLASH ATA Card
HB28C016C6 CompactFlash⑩
HB28C032A6 FLASH ATA Card
相關代理商/技術參數
參數描述
HB2A102K-S265B 制造商:Hitano Enterprise Corp 功能描述:Bulk
HB2A102K-S565B 制造商:Hitano Enterprise Corp 功能描述:Bulk
HB2A103K-S565B 制造商:Hitano Enterprise Corp 功能描述:
HB2A122K-S265B 制造商:Hitano Enterprise Corp 功能描述:
HB2A122K-S565B 制造商:Hitano Enterprise Corp 功能描述:Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*