- 您現在的位置：買賣IC網 > PDF目錄370429 > HB28D064MM2 (Hitachi,Ltd.) MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte PDF資料下載
參數資料
| 型號： | HB28D064MM2 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte |
| 中文描述： | 多媒體16 Mbyte/32 Mbyte/64 Mbyte/128字節 |
| 文件頁數： | 34/88頁 |
| 文件大?。?/td> | 329K |
| 代理商： | HB28D064MM2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
HB28E016/D032/D064/B128MM2
34
Data Transfer Mode
When in Standby State, both CMD and DAT lines are in the push-pull mode. As long as the content of all
CSD registers is not known, the f
PP
clock rate is equal to the slow f
OD
clock rate. SEND_CSD (CMD9)
allows the host to get the Card Specific Data (CSD register), e.g. ECC type, block length, card storage
capacity, maximum clock rate etc..
CMD9, 10
CMD24, 25
CMD12 or
''transfer end''
CMD28, 29, 38
CMD16, 23, 32...37
CMD13
no state transition
in data-transfer mode
CMD7
Stand-by state
(stby)
Disconnect state
(dis)
Programming state
(prg)
Receive-data state
(rcv)
Sending-data state
(data)
Transfer state
(tran)
from all states in
data-transfer mode
data-transfer mode
card-identification mode
CMD15
CMD0
CMD3
''operation
complete''
''operation
complete''
CMD7
CMD12,
''operation
complete''
CMD11, 17, 18, 30
CMD7
CMD7
CMD20, 24, 25, 26, 27, 42
MultiMediaCard State Diagram
(Data Transfer Mode)
The command SELECT_DESELECT_CARD (CMD7) is used to select one card and place it in the
Transfer State. If a previously selected card is in the Transfer State its connection with the host is released
and it will move back to the Stand-by State. Only one card can be, at any time, in the Transfer State. A
selected card is responding the CMD7, the deselected one does not respond to this command. When
CMD7 is sent including the reserved relative card address 0x0000, all cards transfer back to Stand-by State.
This command is used to identify new cards without resetting other already acquired cards. Cards to which
an RCA has already been assigned, do not respond to the identification command flow in this state. All the
data communication in the Data Transfer Mode is consequently a point-to point communication between
the host and the selected card (using addressed commands). All addressed commands are acknowledged by
a response on the CMD line. All read commands (data is sent from the card via data lines) can be
interrupted at any time, by a stop command. The data transfer will terminate and the card will stop or start
working on the next command. The DAT bus line signal level is high when no data is transmitted. A
transmitted data block consists of a start bit (LOW), followed by a continuous data stream. The data stream
contains the net payload data (and error correction bits if an off-card ECC is used). The data stream ends
相關PDF資料 |
PDF描述 |
|---|---|
| HB28E016MM2 | MultiMediaCard 16 Mbyte/32 Mbyte/64 Mbyte/128 MByte |
| HB28C048A6 | FLASH ATA Card |
| HB28C048C6 | CompactFlash⑩ |
| HB28C016A6 | FLASH ATA Card |
| HB28C016C6 | CompactFlash⑩ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HB2A102K-S265B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
| HB2A102K-S565B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
| HB2A103K-S565B | 制造商:Hitano Enterprise Corp 功能描述: |
| HB2A122K-S265B | 制造商:Hitano Enterprise Corp 功能描述: |
| HB2A122K-S565B | 制造商:Hitano Enterprise Corp 功能描述:Bulk |
發布緊急采購，3分鐘左右您將得到回復。