參數資料
型號： HB288016MM1
廠商： Hitachi,Ltd.
英文描述： MultiMediaCard 16 MByte
中文描述： 多媒體16字節
文件頁數： 53/79頁
文件大?。?/td> 233K
代理商： HB288016MM1
HB288016MM1
53
Erase and Write Protect Management
The erase and write protect management procedures in the SPI mode are identical to those of the
MultiMediaCard mode. While the card is erasing or changing the write protection bits of the predefined
sector list, it will be in a busy state and hold the DataOut line low. Figure “No Data Operations” illustrates
a ‘no data’ bus transaction with and without busy signalling.
Data in
Data out
command
response
response busy
command
from
host
to card
from
card
to host
from
card
to host
from
host
to card
‘No Data’ Operations
Reading CID/CSD Registers
Unlike the MultiMediaCard protocol (where the register contents are sent as a command response), reading
the contents of the CSD and CID registers in SPI mode is a simple read-block transaction. The card will
respond with a standard response token (refer to Figure “Read Operation”) followed by a data block of 16
bytes suffixed with a 16 bit CRC. The data timeout for the CSD command cannot be set to the card TAAC
since this value is stored in the CSD. Therefore the standard response timeout value (N
CR
) is used for read
latency of the CSD register.
Reset Sequence
The MultiMediaCard requires a defined reset sequence. After power on reset or CMD0 (software reset) the
card enters an idle state. At this state the only legal host command is CMD1 (SEND_OP_COND) and
CMD58 (READ_OCR). In SPI mode, as opposed to MultiMediaCard mode, CMD1 has no operands and
does not return the contents of the OCR register. Instead, the host may use CMD58 (available in SPI mode
only) to read the OCR register. Furthermore, it is in the responsibility of the host to refrain from accessing
cards that do not support its voltage range. The usage of CMD58 is not restricted to the initializing phase
only, but can be issued at any time. The host must poll the card (by repeatedly sending CMD1) until the
‘in-idle-state’ bit in the card response indicates (by being set to 0) that the card completed its initialization
processes and is ready for the next command. The host must poll the card (by repeatedly sending CMD1)
until the ‘in-idle-state’ bit in the card response indicates (by being set to 0) that the card completed its
initialization processes and is ready for the next command.
相關PDF資料
PDF描述
HB288096C5 CompactFlash(閃速CompactFlash 卡)
HB288160C5 CompactFlash(閃速CompactFlash 卡)
HB2881000A5 FLASH ATA Card 1 GByte
HB2881000A6 FLASH ATA Card
HB288160A5 FLASH ATA Card
相關代理商/技術參數
參數描述
HB288032A5 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card
HB288032A6 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card
HB288032C5 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩
HB288032C6 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩
HB288032MM1 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:MultiMediaCard 32 MByte
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*