- 您現在的位置：買賣IC網 > PDF目錄370428 > HB288016MM1 (Hitachi,Ltd.) MultiMediaCard 16 MByte PDF資料下載
參數資料
| 型號： | HB288016MM1 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | MultiMediaCard 16 MByte |
| 中文描述： | 多媒體16字節 |
| 文件頁數： | 26/79頁 |
| 文件大?。?/td> | 233K |
| 代理商： | HB288016MM1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁
HB288016MM1
26
Basic Commands
(class 0)
and Read Stream Command
(class 1)
CMD
index
Type
Argument
Resp
Abbreviation
Command description
CMD0
bc
[31:0] stuff bits
—
GO_IDLE_STATE
resets all cards to Idle State
CMD1
bcr
[31:0] OCR
without busy
R3
SEND_OP_COND
checks for cards not supporting the full
range of 2.0 V to 3.6 V. After receiving
CMD1 the card sends an R3 response
(refer to Chapter “Responses”).
CMD2
bcr
[31:0] stuff bits
R2
ALL_SEND_CID
asks all cards in ready state to send
their CID*
1
numbers on CMD-line
CMD3
ac
[31:16] RCA
[15:0] stuff bits
R1
SET_RELATIVE_A
DDR
assigns relative address to the card in
identification state.
CMD4
bc
[31:16] DSR
[15:0] stuff bits
—
SET_DSR
programs the DSR of all cards in
stand-by state.
CMD7
ac
[31:16] RCA
[15:0] stuff bits
R1 (only
the
selected
card)
SELECT/
DESELECT_CARD
command toggles a card between the
standby and transfer states or between
the programming and disconnect state.
In both cases the card is selected by
its own relative address while
deselecting the prior selected card.
Address 0 deselects all.
CMD9
ac
[31:16] RCA
[15:0] stuff bits
R2
SEND_CSD
asks the addressed card to send its
card-specific data (CSD)*
2
on CMD-
line.
CMD10 ac
[31:16] RCA
[15:0] stuff bits
R2
SEND_CID
asks the addressed card to send its
card identification (CID) on CMD- line.
CMD11 adtc
[31:0] data
address
R1
READ_DAT_UNTIL
_STOP
reads data stream from the card,
starting at the given address, until a
STOP_TRANSMISSION follows.
CMD12 ac
[31:0] stuff bits
R1b*
3
STOP_TRANSMIS
SION
forces the card to stop transmission
CMD13 ac
[31:16] RCA
[15:0] stuff bits
R1
SEND_STATUS
Asks the addressed card to send its
status register.
CMD15 ac
[31:16] RCA
[15:0] stuff bits
—
GO_INACTIVE_ST
ATE
Sets the card to inactive state in order
to protect the card stack against
communications breakdowns.
Notes: 1. CID register consists of 128 bits (starting with MSB, it is preceded by an additional start bit, ends
with an end bit)
2. CSD register consists of 128 bits (starting with MSB, it is preceded by an additional start bit,
ends with an end bit)
3. This command is indicating the busy status of the MultiMediaCard via the data channel.
相關PDF資料 |
PDF描述 |
|---|---|
| HB288096C5 | CompactFlash(閃速CompactFlash 卡) |
| HB288160C5 | CompactFlash(閃速CompactFlash 卡) |
| HB2881000A5 | FLASH ATA Card 1 GByte |
| HB2881000A6 | FLASH ATA Card |
| HB288160A5 | FLASH ATA Card |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HB288032A5 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288032A6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288032C5 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288032C6 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288032MM1 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:MultiMediaCard 32 MByte |
發布緊急采購，3分鐘左右您將得到回復。