參數資料
型號： HAL805
廠商： MICRONAS SEMICONDUCTOR HOLDING AG
英文描述： Programmable Linear Hall Effect Sensor
中文描述： 可編程線性霍爾效應傳感器
文件頁數： 19/24頁
文件大?。?/td> 373K
代理商： HAL805
PRELIMINARY DATA SHEET
HAL805
Micronas
19
5. Programming of the Sensor
5.1. Definition of Programming Pulses
The sensor is addressed by modulating a serial tele-
gram on the supply voltage. The sensor answers with
a serial telegram on the output pin.
The bits in the serial telegram have a different bit time
for the V
DD
-line and the output. The bit time for the
V
DD
-line is defined through the length of the Sync Bit
at the beginning of each telegram. The bit time for the
output is defined through the Acknowledge Bit.
A logical
“
0
”
is coded as no voltage change within the
bit time. A logical
“
1
”
is coded as a voltage change
between 50% and 80% of the bit time. After each bit, a
voltage change occurs.
5.2. Definition of the Telegram
Each telegram starts with the Sync Bit (logical 0), 3
bits for the Command (COM), the Command Parity Bit
(CP), 4 bits for the Address (ADR), and the Address
Parity Bit (AP).
There are 4 kinds of telegrams:
–
Write a register (see Fig. 5
–
2)
After the AP Bit, follow 14 Data Bits (DAT) and the
Data Parity Bit (DP). If the telegram is valid and the
command has been processed, the sensor answers
with an Acknowledge Bit (logical 0) on the output.
–
Read a register (see Fig. 5
–
3)
After evaluating this command, the sensor answers
with the Acknowledge Bit, 14 Data Bits, and the
Data Parity Bit on the output.
–
Programming the EEPROM cells (see Fig. 5
–
4)
After evaluating this command, the sensor answers
with the Acknowledge Bit. After the delay time t
w
,
the supply voltage rises up to the programming volt-
age.
–
Activate a sensor (see Fig. 5
–
5))
If more than one sensor is connected to the supply
line, selection can be done by first deactivating all
sensors. The output of all sensors will be pulled to
ground by the internal 10 k
resistors. With an Acti-
vate pulse on the appropriate output pin, an individ-
ual sensor can be selected. All following commands
will only be accepted from the activated sensor.
Fig. 5
–
1:
Definition of logical 0 and 1 bit
t
r
t
f
t
p0
t
p0
logical 0
V
DDH
V
DDL
or
t
p0
logical 1
V
DDH
V
DDL
or
t
p0
t
p1
t
p1
Table 5
–
1:
Telegram parameters
Symbol
Parameter
Pin
Min.
Typ.
Max.
Unit
Remarks
V
DDL
Supply Voltage for Low Level
during Programming
1
5
5.6
6
V
V
DDH
Supply Voltage for High Level
during Programming
1
6.8
8.0
8.5
V
t
r
Rise time
1
0.05
ms
t
f
Fall time
1
0.05
ms
t
p0
Bit time on V
DD
1
1.7
1.75
1.8
ms
t
p0
is defined through the Sync Bit
t
pOUT
Bit time on output pin
3
2
3
4
ms
t
is defined through the
Acknowledge Bit
t
p1
Voltage Change for logical 1
1, 3
50
65
80
%
% of t
p0
or t
pOUT
V
DDPROG
Supply Voltage for
Programming the EEPROM
1
11.95
12
12.1
V
t
PROG
Programming Time for EEPROM
1
95
100
105
ms
相關PDF資料
PDF描述
HAL805UT-A Programmable Linear Hall Effect Sensor
HAL805UT-E Programmable Linear Hall Effect Sensor
HAL805UT-K Programmable Linear Hall Effect Sensor
HAL815 Programmable Linear Hall Sensor
HAL815A Programmable Linear Hall Sensor
相關代理商/技術參數
參數描述
HAL805-1 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall-Effect Sensor
HAL805UT-A 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall-Effect Sensor
HAL805UT-E 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall Effect Sensor
HAL805UT-K 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall Effect Sensor
HAL810 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall-Effect Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*