- 您現在的位置：買賣IC網 > PDF目錄370425 > HAL800UT-E (MICRONAS SEMICONDUCTOR HOLDING AG) Programmable Linear Hall Effect Sensor PDF資料下載
參數資料
| 型號： | HAL800UT-E |
| 廠商： | MICRONAS SEMICONDUCTOR HOLDING AG |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | Programmable Linear Hall Effect Sensor |
| 中文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, -1-1mT, 0.35-4.80V, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | PLASTIC, TO-92UT, 3 PIN |
| 文件頁數： | 21/24頁 |
| 文件大小： | 347K |
| 代理商： | HAL800UT-E |
HAL800
Micronas
21
5.3. Telegram Codes
Sync Bit
Each telegram starts with the Sync Bit. This logical 0
pulse defines the exact timing for t
p0
.
Command Bits (COM)
The Command code contains 3 bits and is a binary
number.
Table 5
–
2
shows the available commands and
the corresponding codes for the
HAL 800
.
Command Parity Bit (CP)
This parity bit is 1, if the number of zeros within the 3
Command Bits is uneven. The parity bit is 0, if the
number of zeros is even.
Address Bits (ADR)
The Address code contains 4 bits and is a binary num-
ber.
Table 5
–
3
shows the available addresses for the
HAL 800
registers.
Address parity bit (AP)
This parity bit is 1, if the number of zeros within the 4
Address bits is uneven. The parity bit is 0, if the num-
ber of zeros is even.
Data Bits (DAT)
The 14 Data Bits contain the register information.
The registers use different number formats for the Data
Bits. These formats are explained in
Section 5.4.
In the Write command the last bits are valid. If for
example the TC register (6 bits) is written, only the last
6 bits are valid.
In the Read command the first bits are valid. If for
example the TC register (6 bits) is read, only the first 6
bits are valid.
Data Parity Bit (DP)
This parity bit is 1, if the number of zeros within the
binary number is even. The parity bit is 0, if the number
of zeros is uneven.
Table 5
–
2:
Available Commands
Command
Code
Explanation
READ
2
read a register
WRITE
3
write a register
PROM
4
program all nonvolatile registers (except the lock bits)
ERASE
5
erase all nonvolatile registers (except the lock bits)
LOCKI
6
lock Micronas lockable register
LOCK
7
lock the whole device and switch permanently to the analog-mode
Please note:
The Micronas lock bit (LOCKI) has already been set during production and cannot be reset.
相關PDF資料 |
PDF描述 |
|---|---|
| HAL800UT-K | Programmable Linear Hall Effect Sensor |
| HAL805 | Programmable Linear Hall Effect Sensor |
| HAL805UT-A | Programmable Linear Hall Effect Sensor |
| HAL805UT-E | Programmable Linear Hall Effect Sensor |
| HAL805UT-K | Programmable Linear Hall Effect Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HAL800UT-K | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall Effect Sensor |
| HAL805 | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall Effect Sensor |
| HAL805-1 | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall-Effect Sensor |
| HAL805UT-A | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall-Effect Sensor |
| HAL805UT-E | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Programmable Linear Hall Effect Sensor |
發布緊急采購，3分鐘左右您將得到回復。