- 您現在的位置：買賣IC網 > PDF目錄370366 > GMS81C5032-XXXPL MICROCONTROLLER|8-BIT|CMOS|LDCC|44PIN|PLASTIC PDF資料下載
參數資料
| 型號： | GMS81C5032-XXXPL |
| 英文描述： | MICROCONTROLLER|8-BIT|CMOS|LDCC|44PIN|PLASTIC |
| 中文描述： | 單片機| 8位|的CMOS | LDCC | 44PIN |塑料 |
| 文件頁數： | 24/93頁 |
| 文件大?。?/td> | 853K |
| 代理商： | GMS81C5032-XXXPL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁
GMS81C1404/GMS81C1408
22
June. 2001 Ver 1.2
9. MEMORY ORGANIZATION
The GMS81C1404 and GMS81C1408 have separate ad-
dress spaces for Program memory and Data Memory. Pro-
gram memory can only be read, not written to. It can be up
to 4K /8K bytes of Program memory. Data memory can be
read and written to up to 192 bytes including the stack area.
9.1 Registers
This device has six registers that are the Program Counter
(PC), a Accumulator (A), two index registers (X, Y), the
Stack Pointer (SP), and the Program Status Word (PSW).
The Program Counter consists of 16-bit register.
Figure 9-1 Configuration of Registers
Accumulator:
The Accumulator is the 8-bit general pur-
pose register, used for data operation such as transfer, tem-
porary saving, and conditional judgement, etc.
The Accumulator can be used as a 16-bit register with Y
Register as shown below.
Figure 9-2 Configuration of YA 16-bit Register
X, Y Registers
: In the addressing mode which uses these
index registers, the register contents are added to the spec-
ified address, which becomes the actual address. These
modes are extremely effective for referencing subroutine
tables and memory tables. The index registers also have in-
crement, decrement, comparison and data transfer func-
tions, and they can be used as simple accumulators.
Stack Pointer
: The Stack Pointer is an 8-bit register used
for occurrence interrupts and calling out subroutines. Stack
Pointer identifies the location in the stack to be accessed
(save or restore).
Generally, SP is automatically updated when a subroutine
call is executed or an interrupt is accepted. However, if it
is used in excess of the stack area permitted by the data
memory allocating configuration, the user-processed data
may be lost.
The stack can be located at any position within 00
H
to BF
H
of the internal data memory. The SP is not initialized by
hardware, requiring to write the initial value (the location
with which the use of the stack starts) by using the initial-
ization routine. Normally, the initial value of “BF
H
” is
used.
Note:
The Stack Pointer must be initialized by software be-
cause its value is undefined after RESET.
Example: To initialize the SP
LDX
#0BFH
TXSP
; SP
←
BF
H
Program Counter
: The Program Counter is a 16-bit wide
which consists of two 8-bit registers, PCH and PCL. This
counter indicates the address of the next instruction to be
executed. In reset state, the program counter has reset rou-
tine address (PC
H
:0FF
H
, PC
L
:0FE
H
).
Program Status Word
: The Program Status Word (PSW)
contains several bits that reflect the current state of the
CPU. The PSW is described in Figure 9-3 . It contains the
Negative flag, the Overflow flag, the Break flag the Half
Carry (for BCD operation), the Interrupt enable flag, the
Zero flag, and the Carry flag.
[Carry flag C]
This flag stores any carry or borrow from the ALU of CPU
after an arithmetic operation and is also changed by the
Shift Instruction or Rotate Instruction.
[Zero flag Z]
This flag is set when the result of an arithmetic operation
or data transfer is “0” and is cleared by any other result.
A
ACCUMULATOR
X REGISTER
Y REGISTER
STACK POINTER
PROGRAM COUNTER
PROGRAM STATUS
WORD
X
Y
SP
PCL
PCH
PSW
Two 8-bit Registers can be used as a “YA” 16-bit Register
Y
A
Y
A
SP
0
Stack Address (000
H
~ 0BF
H
)
8
15
0
7
Hardware fixed
相關PDF資料 |
PDF描述 |
|---|---|
| GMS81C5032-XXXPLT | MICROCONTROLLER|8-BIT|CMOS|LDCC|44PIN|PLASTIC |
| GMS81C5032-XXXQ | MICROCONTROLLER|8-BIT|CMOS|QFP|44PIN|PLASTIC |
| GMS81C5032-XXXQT | MICROCONTROLLER|8-BIT|CMOS|QFP|44PIN|PLASTIC |
| GMS81C5032-XXXSK | MICROCONTROLLER|8-BIT|CMOS|DIP|28PIN|PLASTIC |
| GMS81C7208 | NET CENTER 48" W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GMS81C5032-XXXPLT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|LDCC|44PIN|PLASTIC |
| GMS81C5032-XXXQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|QFP|44PIN|PLASTIC |
| GMS81C5032-XXXQT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|QFP|44PIN|PLASTIC |
| GMS81C5032-XXXSK | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|CMOS|DIP|28PIN|PLASTIC |
| GMS81C5108 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:HYNIX SEMICONDUCTOR INC. 8-BIT SINGLE-CHIP MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。