- 您現在的位置：買賣IC網 > PDF目錄67593 > FW250R1 (LINEAGE POWER LLC) 1-OUTPUT 256.95 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FW250R1 |
| 廠商： | LINEAGE POWER LLC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 256.95 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | MODULE-20 |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 561K |
| 代理商： | FW250R1 |
12
Lineage Power
Data Sheet
April 2008
36 Vdc to 75 Vdc Input, 28 Vdc Output; 250 W to 300 W
FW250R1 and FW300R1 Power Modules: dc-dc Converters:
Feature Descriptions (continued)
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with an overtemperature shutdown circuit.
The shutdown circuit will not engage unless the unit is
operated above the maximum case temperature.
Recovery from overtemperature shutdown is
accomplished by cycling the dc input power off for at
least 1.0 second or toggling the primary referenced
on/off signal for at least 1.0 second.
Forced Load Sharing (Parallel Operation)
For either redundant operation or additional power
requirements, the power modules can be congured for
parallel operation with forced load sharing (see
Figure 17). For a typical redundant conguration,
Schottky diodes or an equivalent should be used to
protect against short-circuit conditions. Because of the
remote sense, the forward-voltage drops across the
Schottky diodes do not affect the set point of the
voltage applied to the load. For additional power
requirements, where multiple units are used to develop
combined power in excess of the rated maximum, the
Schottky diodes are not needed.
Good layout techniques should be observed for noise
immunity. To implement forced load sharing, the follow-
ing connections must be made:
s
The parallel pins of all units must be connected
together. The paths of these connections should be
as direct as possible.
s
All remote-sense pins should be connected to the
power bus at the same point, i.e., connect all
SENSE(+) pins to the (+) side of the power bus at the
same point and all SENSE(–) pins to the (–) side of
the power bus at the same point. Close proximity and
directness are necessary for good noise immunity.
When not using the parallel feature, leave the
PARALLEL pin open.
8-581 (C)
Figure 17. Wiring Conguration for Redundant
Parallel Operation
Power Good Signal
The PWR GOOD pin provides an open-drain signal
(referenced to the SENSE(–) pin) that indicates the
operating state of the module. A low impedance
(<100
) between PWR GOOD and SENSE(–) indi-
cates that the module is operating. A high impedance
(>1 M
) between PWR GOOD and SENSE(–) indi-
cates that the module is off or has failed. The PWR
GOOD pin can be pulled up through a resistor to an
external voltage to facilitate sensing. This external volt-
age level must not exceed 40 V, and the current into the
PWR GOOD pin during the low-impedance state
should be limited to 1 mA maximum.
VO(+)
PARALLEL
SENSE(+)
SENSE(–)
VO(–)
CASE
VI(+)
ON/OFF
VI(–)
VO(+)
PARALLEL
SENSE(+)
SENSE(–)
VO(–)
CASE
VI(+)
ON/OFF
VI(–)
相關PDF資料 |
PDF描述 |
|---|---|
| FW330D1 | 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE |
| FW330F1 | 1-OUTPUT 330 W DC-DC REG PWR SUPPLY MODULE |
| FW330G71-56T | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
| FW330S3R671-56 | 1-OUTPUT 330 W DC-DC REG PWR SUPPLY MODULE |
| FW330F1-33T | 1-OUTPUT 330 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FW250S6R0 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-to-DC Voltage Converter |
| FW250-TL-E | 制造商:SANYO 功能描述:N+N 60V 3A 0.145 SOP8 Tape & Reel 制造商:SANYO Semiconductor Co Ltd 功能描述:MOSFET NN CH 60V 3A SOT96 制造商:Sanyo 功能描述:0 |
| FW256 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:General-Purpose Switching Device Applications |
| FW257 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:N CHANNEL MOS SILICON TRANSISTOR |
| FW257-TL-E | 制造商:SANYO 功能描述:N+N 100V 2A 0.22 SOP8 Tape & Reel 制造商:SANYO Semiconductor Co Ltd 功能描述:MOSFET NN CH 100V 2A SOT96 制造商:Sanyo 功能描述:0 |
發布緊急采購，3分鐘左右您將得到回復。