- 您現在的位置：買賣IC網 > PDF目錄223808 > FT2232HL-TRAY (Future Technology Devices International Ltd) PDF資料下載
參數資料
| 型號： | FT2232HL-TRAY |
| 廠商： | Future Technology Devices International Ltd |
| 元件分類： | 總線控制器 |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 |
| 封裝： | LEAD FREE, LQFP-64 |
| 文件頁數： | 4/63頁 |
| 文件大?。?/td> | 1598K |
| 代理商： | FT2232HL-TRAY |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
Copyright 2010 Future Technology Devices International Limited
12
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 2.10
Clearance No.: FTDI#77
3.4.2 FT2232H pins used in an FT245 Style Synchronous FIFO Interface
The FT2232H only channel A can be configured as a FT245 style synchronous FIFO interface. When
configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.5. To
enter this mode the external EEPROM must be set to make port A 245 mode. A software command (Set
Bit Mode option) is then sent by the application to the FTDI driver to tell the chip to enter single channel
synchronous FIFO mode. In this mode the B channel is not available as all resources have been switched
onto channel A. In this mode, data is written or read on the rising edge of the CLKOUT.
Channel A
Pin No.
Name
Type
FT245 Configuration Description
24,23,22,21,
19,18,17,16
ADBUS[7:0]
I/O
D7 to D0 bidirectional FIFO data. This bus is normally input unless
OE# is low.
26
RXF#
OUTPUT
When high, do not read data from the FIFO. When low, there is data
available in the FIFO which can be read by driving RD# low. When in
synchronous mode, data is transferred on every clock that RXF# and
RD# are both low. Note that the OE# pin must be driven low at least
1 clock period before asserting RD# low.
27
TXE#
OUTPUT
When high, do not write data into the FIFO. When low, data can be
written into the FIFO by driving WR# low. When in synchronous
mode, data is transferred on every clock that TXE# and WR# are both
low.
28
RD#
INPUT
Enables the current FIFO data byte to be driven onto D0...D7 when
RD# goes low. The next FIFO data byte (if available) is fetched from
the receive FIFO buffer each CLKOUT cycle until RD# goes high.
29
WR#
INPUT
Enables the data byte on the D0...D7 pins to be written into the
transmit FIFO buffer when WR# is low. The next FIFO data byte is
written to the transmit FIFO buffer each CLKOUT cycle until WR# goes
high.
32
CLKOUT
OUTPUT
60 MHz Clock driven from the chip. All signals should be synchronized
to this clock.
33
OE#
INPUT
Output enable when low to drive data onto D0-7. This should be
driven low at least 1 clock period before driving RD# low to allow for
data buffer turn-around.
30
SIWU
INPUT
The Send Immediate / WakeUp signal combines two functions on a
single pin. If USB is in suspend mode (PWREN# = 1) and remote
wakeup is enabled in the EEPROM , strobing this pin low will cause the
device to request a resume on the USB Bus. Normally, this can be
used to wake up the Host PC.
During normal operation (PWREN# = 0), if this pin is strobed low any
data in the device TX buffer will be sent out over USB on the next
Bulk-IN request from the drivers regardless of the pending packet
size. This can be used to optimize USB transfer speed for some
applications. Tie this pin to VCCIO if not used. (Also see note 1, 2, 3
in section 4.12)
Table 3.5 Channel A FT245 Style Synchronous FIFO Configured Pin Descriptions
For a functional description of this mode, please refer to section 4.4
相關PDF資料 |
PDF描述 |
|---|---|
| FT245BL | |
| FT245BQ | |
| FT245BM | |
| FTL-1419-3D | FIBER OPTIC TRANSCEIVER, 1290-1340nm, 1250Mbps(Tx), 1250Mbps(Rx), PANEL MOUNT |
| FTLF1321P1BTL | FIBER OPTIC TRANSCEIVER, 1270-1360nm, 2667Mbps(Tx), 2667Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT2232HMINIMODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed FT2232H Evaluation Module 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB to serial/FIFO development module |
| FT2232H-MINI-MODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC,EVALUATION MODULE;FT2232H;USB HI-SPEED |
| FT2232HQ | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - QFN-64 |
| FT2232HQ_MINI_ MODULE | 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| FT2232HQ-4000 | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
發布緊急采購，3分鐘左右您將得到回復。