參數資料
型號: FM3204-G
元件分類: 消費家電
英文描述: SPECIALTY CONSUMER CIRCUIT, PDSO14
封裝: GREEN, MS-012AB, SOIC-14
文件頁數: 6/21頁
文件大?。?/td> 424K
代理商: FM3204-G
FM3204/16/64/256
Rev. 3.1
July 2010
Page 14 of 21
three bytes of a write operation to set the internal
address followed by subsequent read operations.
To perform a selective read, the bus master sends out
the slave address with the LSB set to 0. This specifies
a write operation. According to the write protocol,
the bus master then sends the address bytes that are
loaded into the internal address latch. After the
FM32xx acknowledges the address, the bus master
issues a Start condition. This simultaneously aborts
the write operation and allows the read command to
be issued with the slave address LSB set to a 1. The
operation is now a read from the current address.
Read operations are illustrated below.
Companion Write Operation
All Companion writes operate in a similar manner to
memory writes. The distinction is that a different
device ID is used and only one byte of address is
needed instead of two. Figure 15 illustrates a single
byte write to this device.
Companion Read Operation
As with writes, a read operation begins with the
Slave Address. To perform a register read, the bus
master supplies a Slave Address with the LSB set to
1. This indicates that a read operation is requested.
After receiving the complete Slave Address, the
FM32xx will begin shifting data out from the current
register address on the next clock. Auto-increment
operates for the special function registers as with the
memory address. A current address read for the
registers look exactly like the memory except that the
device ID is different.
The FM32xx contains two separate address registers,
one for the memory address and the other for the
register address. This allows the contents of one
address register to be modified without affecting the
current address of the other register. For example,
this would allow an interrupted read to the memory
while still providing fast access to a companion
register. A subsequent memory read will then
continue from the memory address where it
previously left off, without requiring the load of a
new memory address. However, a write sequence
always requires an address to be supplied.
Figure 12. Current Address Memory Read
Figure 13. Sequential Memory Read
S
A
Slave Address
1
Data Byte
1
P
By Master
By FM32xx
Start
Address
Stop
Acknowledge
No
Acknowledge
Data
S
A
Slave Address
1
Data Byte
1 P
By Master
By FM32xx
Start
Address
Stop
Acknowledge
No
Acknowledge
Data
Data Byte
A
Acknowledge
相關PDF資料
PDF描述
FM3216-G SPECIALTY CONSUMER CIRCUIT, PDSO14
FM3264-G SPECIALTY CONSUMER CIRCUIT, PDSO14
FM32272-GTR SPECIALTY CONSUMER CIRCUIT, PDSO14
FM32272-G SPECIALTY CONSUMER CIRCUIT, PDSO14
FM32274-GTR SPECIALTY CONSUMER CIRCUIT, PDSO14
相關代理商/技術參數
參數描述
FM3204-GTR 功能描述:監控電路 4K w/Pwr Mon WDT Bat Sw Pwr Fail RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
FM3204-S 功能描述:監控電路 4K w/Pwr Mon WDT Bat Sw Pwr Fail RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
FM3204-STR 功能描述:監控電路 4K w/Pwr Mon WDT Bat Sw Pwr Fail RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲(典型值):10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
FM320A 制造商:RECTRON 制造商全稱:Rectron Semiconductor 功能描述:SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 to 60 Volts CURRENT 3.0 Amperes
FM320-A 制造商:FORMOSA 制造商全稱:Formosa MS 功能描述:Chip Schottky Barrier Diodes - Silicon epitaxial planer type