- 您現在的位置：買賣IC網 > Datasheet目錄38 > FAN6921MRMY (Fairchild Semiconductor)IC CTLR PFC/FLYBACK 16-SOICN Datasheet資料下載
參數資料
| 型號： | FAN6921MRMY |
| 廠商： | Fairchild Semiconductor |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 1210K |
| 描述： | IC CTLR PFC/FLYBACK 16-SOICN |
| 標準包裝： | 2,500 |
| 模式： | 臨界傳導（CRM） |
| 電流 - 啟動： | 10µA |
| 電源電壓： | 8.5 V ~ 25 V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
?2009 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FAN6921MR Rev. 1.0.4
5
Pin Definitions (Continued)
Pin # Name Description
6
OPFC
Totem-pole driver output to drive the external power MOSFET. The clamped gate output voltage
is 15.5 V.
7
VDD
Power supply. The threshold voltage for startup and turn-off is 18 V and 7.5 V, respectively. The
startup current is less than 30糀 and the operating current is lower than 10 mA.
8
OPWM
Totem-pole output generates the PWM signal to drive the external power MOSFET. The clamped
gate output voltage is 17.5 V.
9
GND The power ground and signal ground.
10
DET
This pin is connected to an auxiliary winding of the PWM transformer through a resistor divider for
the following purposes:
? Producing an offset voltage to compensate the threshold voltage of PWM current limit for
providing over-power compensation. The offset is generated in accordance with the input
voltage when PWM switch is on.
? Detecting the valley voltage signal of drain voltage of the PWM switch to achieve the valley
voltage switching and minimize the switching loss on PWM switch.
? Providing output over-voltage protection. A voltage comparator is built-in to the DET pin. The
DET pin detects the flat voltage through a voltage divider paralleled with auxiliary winding. This
flat voltage is reflected to the secondary winding during PWM inductor discharge time. If output
OVP and this flat voltage is higher than 2.5 V, the controller enters latch mode and stops all
PFC and PWM switching operation.
11
FB
Feedback voltage pin. This pin is used to receive output voltage level signal to determine PWM
gate duty for regulating output voltage. The FB pin voltage can also activate open-loop, over-load
protection, and output-short circuit protection if the FB pin voltage is higher than a threshold of
around 4.2 V for more than 50 ms.The input impedance of this pin is a 5 k& equivalent
resistance. A 1/3 attenuator is connected between the FB pin and the input of the CSPWM/FB
comparator.
12
RT
Adjustable over-temperature protection and external latch triggering. A constant current is flowed
out of the RT pin. When RT pin voltage is lower than 0.8 V (typical), latch mode protection is
activated and stops all PFC and PWM switching operation until the AC plug is removed.
13
VIN
Line-voltage detection for brown-in / out protections. This pin can receive the AC input voltage
level through a voltage divider. The voltage level of the VIN pin is not only used to control
RANGE pins status, but it can also perform brown-in / out protection for AC input voltage UVP.
14
ZCD
Zero-current detection for the PFC stage. This pin is connected to an auxiliary winding coupled to
PFC inductor winding to detect the ZCD voltage signal once the PFC inductor current discharges
to zero. When the ZCD voltage signal is detected, the controller starts a new PFC switching
cycle. When the ZCD pin voltage is pulled to under 0.2 V (typical), it disables the PFC stage and
the controller stops PFC switching. This can be realized with an external circuit if disabling the
PFC stage is desired.
15
NC
No connection
16
HV
High-voltage startup. HV pin is connected to the AC line voltage through a resistor
(100 k& typical) for providing a high charging current to V
DD
capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| FAN6961SZ | IC PFC CONTROLLER DCM 8SOP |
| FAN6982MY | IC CTLR PFC CCM 14-SOICN |
| FAN7527BN | IC PFC CTRLR TRANSITION 8DIP |
| FAN7529MX | IC PFC CTRLR CRM/TRANSITION 8SOP |
| FAN7930BM | IC PFC CTLR CRITICAL CONF 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN6961 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Interleaved Dual BCM PFC Controllers |
| FAN6961BMY | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN6961DY | 功能描述:功率因數校正 IC Green mode PFC Fwd PWM Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| FAN6961DZ | 功能描述:功率因數校正 IC Green mode PFC Fwd PWM Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| FAN6961SY | 功能描述:功率因數校正 IC Green mode PFC Fwd PWM Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。