- 您現在的位置：買賣IC網 > PDF目錄17046 > EVAL-AD7606EDZ (Analog Devices Inc)EVAL BOARD FOR AD7606 PDF資料下載
參數資料
| 型號： | EVAL-AD7606EDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/36頁 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR AD7606 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 200k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 在以下條件下的電源（標準）： | 100mW @ 200kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7606 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD7606/AD7606-6/AD7606-4
Data Sheet
Rev. C | Page 26 of 36
CONVERSION CONTROL
Simultaneous Sampling on All Analog Input Channels
The AD7606/AD7606-6/AD7606-4 allow simultaneous sampling
of all analog input channels. All channels are sampled simul-
taneously when both CONVST pins (CONVST A, CONVST B)
are tied together. A single CONVST signal is used to control both
CONVST x inputs. The rising edge of this common CONVST
signal initiates simultaneous sampling on all analog input channels
(V1 to V8 for the AD7606, V1 to V6 for the AD7606-6, and V1
to V4 for the AD7606-4).
The AD7606 contains an on-chip oscillator that is used to
perform the conversions. The conversion time for all ADC
channels is tCONV. The BUSY signal indicates to the user when
conversions are in progress, so when the rising edge of CONVST
is applied, BUSY goes logic high and transitions low at the end
of the entire conversion process. The falling edge of the BUSY
signal is used to place all eight track-and-hold amplifiers back
into track mode. The falling edge of BUSY also indicates that
the new data can now be read from the parallel bus (DB[15:0]),
the DOUTA and DOUTB serial data lines, or the parallel byte bus,
DB[7:0].
Simultaneously Sampling Two Sets of Channels
The AD7606/AD7606-6/AD7606-4 also allow the analog input
channels to be sampled simultaneously in two sets. This can be
used in power-line protection and measurement systems to
compensate for phase differences introduced by PT and CT
transformers. In a 50 Hz system, this allows for up to 9° of phase
compensation; and in a 60 Hz system, it allows for up to 10° of
phase compensation.
This is accomplished by pulsing the two CONVST pins
independently and is possible only if oversampling is not in use.
CONVST A is used to initiate simultaneous sampling of the
first set of channels (V1 to V4 for the AD7606, V1 to V3 for the
AD7606-6, and V1 and V2 for the AD7606-4); and CONVST B
is used to initiate simultaneous sampling on the second set of
analog input channels (V5 to V8 for the AD7606, V4 to V6 for
the AD7606-6, and V3 and V4 for the AD7606-4), as illustrated
in Figure 44. On the rising edge of CONVST A, the track-and-
hold amplifiers for the first set of channels are placed into hold
mode. On the rising edge of CONVST B, the track-and-hold
amplifiers for the second set of channels are placed into hold
mode. The conversion process begins once both rising edges
of CONVST x have occurred; therefore BUSY goes high on the
rising edge of the later CONVST x signal. In Table 3, Time t5
indicates the maximum allowable time between CONVST x
sampling points.
There is no change to the data read process when using two
separate CONVST x signals.
Connect all unused analog input channels to AGND. The results
for any unused channels are still included in the data read because
all channels are always converted.
CONVST A
CONVST B
BUSY
CS/RD
DATA: DB[15:0]
FRSTDATA
V1
V2
V3
V7
V8
t5
tCONV
V1 TO V4 TRACK-AND-HOLD
ENTER HOLD
V5 TO V8 TRACK-AND-HOLD
ENTER HOLD
AD7606 CONVERTS
ON ALL 8 CHANNELS
08479-
042
Figure 44. AD7606 Simultaneous Sampling on Channel Sets While Using Independent CONVST A and CONVST B Signals—Parallel Mode
相關PDF資料 |
PDF描述 |
|---|---|
| STD09W-Y | WIRE & CABLE MARKERS |
| EVAL-AD7327SDZ | BOARD EVAL FOR AD7327SDZ |
| STD01W-Y | WIRE & CABLE MARKERS |
| MPC8323E-RDB | BOARD REFERENCE DESIGN |
| GMC05DRAH-S734 | CONN EDGECARD 10POS .100 R/A SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7607EDZ | 功能描述:EVAL BOARD FOR AD7607 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7608EDZ | 功能描述:BOARD EVAL FOR AD7608 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7609EDZ | 功能描述:BOARD EVAL FOR AD7609 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7610CB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 16BIT, 250 KSPS, UNIPOLAR/BIPOLAR PROGRAMMABLE - Bulk |
| EVAL-AD7610CBZ | 功能描述:BOARD EVALUATION FOR AD7610 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。